1995 Mercury Grand Marquis Ls Sedan 4-door 4.6l on 2040-cars

Auto blog

Junkyard Gem: 1955 Mercury Montclair Coupe

I find plenty of 1950s Detroit vehicles in the big self-service car graveyards I frequent, but most of them are fairly ordinary sedans that never stood much chance of getting fixed up and put back on the road. Such is not the case with today's Junkyard Gem, which is a top-trim-level, heavily optioned hardtop coupe from one of the most desirable model years of the tailfins-and-chrome postwar era. Nearly every Mercury model ever made was a Ford model with some cosmetic changes applied, and the '55s looked very similar to their mechanically identical Ford brethren. In 1955, the new Mercury came in three trim levels: the entry-level Custom, the medium-zoot Monterey, and the glitzy Montclair. Each was available as a hardtop coupe and four-door sedan, with wagon versions of the Custom and Monterey. The Montclair could be purchased as a convertible or with the wild "Sun Valley" glass roof. The Montclair got its own line of hallucinogenic two-tone interiors, in order to make the daily lives of Europeans feel even more gray and penurious (the UK only dropped food rationing in 1954, and the two Germanies were still clearing the rubble of their blown-up cities). This car's upholstery has been bleached by decades of sitting outside in the harsh High Plains climate, but it started out as vivid red and white "Chromatex" fabric. The list price on this car was $2,631, or about $29,200 in 2022 dollars. The Sun Valley and convertible Montclair each cost $2,712 ($30,100 today). Ford didn't offer a corresponding hardtop coupe in 1955, though the Fairlane Crown Victoria two-door did look extremely snazzy (and cost a mere $2,302— $25,545 now— with the same V8 engine as the Monterey). Meanwhile, Oldsmobile offered the handsome 88 Super Holiday Coupe for $2,714, though the Montclair had the more powerful engine. Oldsmobile had been selling new cars with overhead-valve V8s since the 1949 model year, while Ford didn't ditch the Model A-era flathead V8 for new U.S.-market cars until the 1954 model year (you could buy a new Simca Esplanada in Brazil with an Ardun-headed Ford V8-60 all the way until 1969). GM's Chevrolet Division got all the press in 1955 with the introduction of the brand-new small-block V8 engine, but Ford's 292-cubic-inch (4.8-liter) Y-Block V8 made more power than the 265-cube (4.3-liter) Chevy and the 324ci Olds Rocket 88.

This Mercury Cougar Eliminator is a lovely '69 survivor

If you have an overachieving brother/sister/cousin/friend (or whoever), you might know this feeling well; it can be tough to live up to those standards. In many ways, that notion can also describe the Mercury Cougar and its pioneering Ford Mustang sibling. Quite the act to follow, no? Happily though, the Cougar proved to be different enough from its Mustang relative to make a big splash, and perhaps no more so than in its racy "Eliminator" trim, new for 1969. This is one such heady Mercury, dressed in sporty Competition Orange paint, and claimed to be an unrestored "survivor." Need it in your life? The '69 Mercury Cougar Eliminator recently popped up on eBay in Chepachet, Rhode Island . The genesis of the Mercury Cougar began in 1967, really with one singular purpose—to bridge the gap between the Ford Mustang and the Ford Thunderbird with a more upscale, stylish, and chiefly more "European" feeling pony car. It's safe to say the Cougar fit the bill. Using the Mustang chassis as a base, the early Cougars were about three inches longer than their 'Stang cousins and offered better legroom, sleek front and rear fascias, and a more luxe interior. Don't mistake "upscale" for "soft" however; come 1969 the Eliminator package gave the Cougar a seriously mean attitude. Spec-up the interior package and you received high-back bucket seats, a Rallye clock, wood-rimmed steering wheel, and padded interior moldings among other custom trims. Outside is where the Eliminator really struts its stuff, though. Eliminators came equipped with a blacked-out grille, special steel wheels, an aggressive front splitter and rear wing, plus racy decals and side stripes. Four color choices were available — Competition Orange, Bright Blue Metallic, White, and Bright Yellow. As standard, the '69 Mercury Cougar Eliminator came equipped with a 351 cubic inch V8, boasting 290 horsepower, as seen in the case of this car. More powerful options were also available, as noted by Barnfinds, which included a big 390 cubic inch V8 (320 hp), a high-revving Boss 302 V8, and the gargantuan 428 Cobra Jet V8. Peek beneath the body of this Cougar and the 351ci V8 is hooked up to a desirable close-ratio four-speed manual transmission, showing a claimed 35,243 miles. Though the mileage isn't verified, the car's overall condition and wear would suggest the readings to be true. Befitting those low miles, this unrestored Cougar does carry quite the high price — a tall $32,000.

Ringbrothers shows off Coyote-powered 1968 Mercury Cougar

We'll openly admit that not every SEMA build is our cup of tea. But this? A tastefully resto-modded 1968 Mercury Cougar with a 460-horsepower Ford Mustang V8? Yeah, this is right in our wheelhouse. Sadly, there was no in-pwerson SEMA show in 2020, so we missed out on gems like this one. SEMA or no SEMA, the aftermarket carries on, and co-owners Jim and Mike Ring of Ringbrothers (get it?) saw no reason to let their time and effort go to waste.  When they're not building wild customs (see: 1,100-horsepower 1972 AMC Javelin AMX) or more subtle showcases (such as this Cougar or their 1971 K5 Chevy Blazer build from 2018), the folks at Ringbrothers crank out factory reproduction parts, whether for old-fashioned restoration or modification purposes. While '60s muscle cars are recurring build subjects for the two, the Cougar was the first of its kind they tackled.  Keeping it in the family, Ringbrothers sourced a Ford 5.0-liter "Coyote" V8 and a 10-Speed Automatic (lifted from an F-150 Raptor, incidentally) for the build. They didn't stop with the driveline, of course. The suspension was overhauled with a little help from DSE and a set of HRE Series C1 C103 Forged 3-Piece wheels were thrown over upgraded brakes.  "We put our heart into each car we build, and this Cougar is no exception," Jim said. "The finished product is mild and classy, yet any enthusiast instantly knows it's not stock. I imagine this is what Mercury designers would have come up with if they were building the Cougar today." "While we couldn't bring the car to the SEMA Show, we hope it can be shown to the public soon," Mike said. "We had never done a Cougar before, so this was a fun build. I love working with new shapes and coming up with new ideas." There's plenty to appreciate about this Cougar apart from the mechanicals, too. The finish is Augusta Green Metallic (courtesy of BASF), which was a factory color in 1968. You may know it by another name: Highland Green. There are a few custom exterior touches, but they're quite subtle and styled to be period-correct. The interior was also restored and updated, and it's where you'll find the only thing we're not fond of: that big, fat truck shifter. Gearbox choices notwithstanding, it's a bit of an eyesore. But considering how gorgeous the rest is, we'll give it a pass.  Related Video: