1995 Mercury Grand Marquis 4.6 V8 on 2040-cars

Auto blog

Junkyard Gem: 1972 Mercury Cougar XR-7

Starting with the 1939 model year and continuing through 2011, the rule in Dearborn was that most Ford models would get a dressed-up sibling wearing Mercury badges (and Canadians even got Mercury F-100s and Econolines). When the Mustang first hit showrooms in 1964, the countdown for a Mercurized version began. That car, the Cougar, debuted as a 1967 model marketed as "the man's car." Today's Junkyard Gem is a much-abused example of the early-1970s Cougar, found in a San Francisco Bay Area car graveyard a while back. Just as the Mustang packed on weight and price as the 1960s became the 1970s, the even more heavily gingerbreaded Cougar did the same. For 1971 through 1973, the Cougar was still based on the Mustang chassis but weighed several hundred additional pounds and was more than seven inches longer. The curb weight for this car was 3,298 pounds, versus 2,941 pounds for the lightest '72 Mustang coupe. Yes, there's a Mustang underneath all that chrome! When the Mustang went to a modified Pinto chassis starting in the 1974 model year, the Cougar moved over to the midsize Torino platform and stayed there until it rejoined the Mustang on the Fox platform for 1980 (though the honor of being the Mustang's near-twin went to the Mercury Capri at that point). For 1989, the Cougar became an MN12 Thunderbird sibling, where it remained through its 30th anniversary … and then the Cougar got the axe. The Cougar story wasn't done at that point, however, because the name got revived in 1999 with a Mondeo-based version that lasted through 2002 and bears the distinction of being one of the few Mercury models with no corresponding Ford-badged counterpart. Along the way, there were Cougar sedans and even station wagons, with the curb weight of the heaviest-ever Cougar bloating to well over two tons (the winner of that honor is the 1977 Cougar Villager wagon, scaling in at an astounding 4,482 pounds). In 1972, though, all new Cougars were coupes or convertibles, and all of them came with factory V8 power. The build tag on this one tells us that it was assembled at the River Rouge compound in Dearborn and sold via the Kansas City sales office. That tells us that someone drove this car to California after buying it in the Midwest; Ford also built 1972 Cougars in San Jose, so California Mercury shoppers would have bought locally-produced ones. It's a top-end XR-7 in Medium Bright Yellow paint, with the interior in Medium Ginger.

Ford recalling 370,000 Crown Vic, Grand Marquis and Town Car models

The Detroit News is reporting that Ford will recall some 370,000 Crown Victoria (pictured), Mercury Grand Marquis and Lincoln Town Car vehicles from model years 2005 through 2011, for an issue regarding the lower intermediate steering shaft. 355,000 of the vehicles in question were sold in the US, with the other 15,000 sold in Canada.
The report indicates that corrosion of the lower intermediate steering shaft could cause a "loss of steering," presumably because of a partial or complete failure of the part. The report points out the dealers will inspect and replace the offending steering component for recalled cars, and may also secure a lower steering column bearing and replace the upper intermediate steering shaft as needed. The company is unaware of any reports of the faulty part causing any accidents or injuries.
Ford helpfully lists states in which corrosion is more likely to have taken place, mostly in the Snow Belt, as you might guess. Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, Wisconsin, West Virginia, and the District of Columbia are listed.

NHTSA investigating Ford's solution to May 2014 power steering recall

The National Highway Traffic Safety Administration is investigating a complaint that Ford's response to a May 2014 recall of the 2008 to 2011 Ford Escape and Mercury Mariner doesn't quite go far enough to solve a troubling power-steering problem. Roughly a year ago, Ford recalled nearly a million vehicles after it was found that a problem with the torque sensor's communication with the power steering control module could cut steering assistance for drivers. While manual steering would still be available, the problem was enough to ask drivers to report in to have the PSCM inspected, and if necessary, replaced (along with the torque sensor, or in dramatic cases, the entire steering column). That would only happen, though, if trouble codes were being thrown. If there weren't any problems, dealers were told to simply update the PSCM's software so that any issues between it and the torque sensor would simply throw a visual and audio warning – power steering would still be maintained. The petitioner claimed that following the recall work, he still experienced a problem with the torque sensor. According to NHTSA, a claim was made that Ford didn't go far enough in its solution to the problem, and that "the software update itself may in fact cause further issues with the affected vehicle's power steering, causing it to fail, and ultimately requiring replacement of the torque sensor or entire steering column." The petition was filed in early February and is now officially being looked into by NHTSA.