1997 Mercury Cougar Only 55k 1-owner Ext Warranty on 2040-cars

Auto blog

This Mercury Cougar Eliminator is a lovely '69 survivor

If you have an overachieving brother/sister/cousin/friend (or whoever), you might know this feeling well; it can be tough to live up to those standards. In many ways, that notion can also describe the Mercury Cougar and its pioneering Ford Mustang sibling. Quite the act to follow, no? Happily though, the Cougar proved to be different enough from its Mustang relative to make a big splash, and perhaps no more so than in its racy "Eliminator" trim, new for 1969. This is one such heady Mercury, dressed in sporty Competition Orange paint, and claimed to be an unrestored "survivor." Need it in your life? The '69 Mercury Cougar Eliminator recently popped up on eBay in Chepachet, Rhode Island . The genesis of the Mercury Cougar began in 1967, really with one singular purpose—to bridge the gap between the Ford Mustang and the Ford Thunderbird with a more upscale, stylish, and chiefly more "European" feeling pony car. It's safe to say the Cougar fit the bill. Using the Mustang chassis as a base, the early Cougars were about three inches longer than their 'Stang cousins and offered better legroom, sleek front and rear fascias, and a more luxe interior. Don't mistake "upscale" for "soft" however; come 1969 the Eliminator package gave the Cougar a seriously mean attitude. Spec-up the interior package and you received high-back bucket seats, a Rallye clock, wood-rimmed steering wheel, and padded interior moldings among other custom trims. Outside is where the Eliminator really struts its stuff, though. Eliminators came equipped with a blacked-out grille, special steel wheels, an aggressive front splitter and rear wing, plus racy decals and side stripes. Four color choices were available — Competition Orange, Bright Blue Metallic, White, and Bright Yellow. As standard, the '69 Mercury Cougar Eliminator came equipped with a 351 cubic inch V8, boasting 290 horsepower, as seen in the case of this car. More powerful options were also available, as noted by Barnfinds, which included a big 390 cubic inch V8 (320 hp), a high-revving Boss 302 V8, and the gargantuan 428 Cobra Jet V8. Peek beneath the body of this Cougar and the 351ci V8 is hooked up to a desirable close-ratio four-speed manual transmission, showing a claimed 35,243 miles. Though the mileage isn't verified, the car's overall condition and wear would suggest the readings to be true. Befitting those low miles, this unrestored Cougar does carry quite the high price — a tall $32,000.

Ford recalls over 953,000 vehicles to replace Takata airbag inflators

DETROIT — Ford is recalling more than 953,000 vehicles worldwide to replace Takata passenger airbag inflators that can explode and hurl shrapnel. The move includes over 782,000 vehicles in the U.S. and is part of the largest series of recalls in U.S. history. Included are the 2010 Ford Edge and Lincoln MKX, the 2010 and 2011 Ford Ranger, the 2010 to 2012 Ford Fusion and Lincoln MKZ, the 2010 and 2011 Mercury Milan, and the 2010 to 2014 Ford Mustang. Some of the recalls may be limited to specific geographic areas of the U.S. Takata used the chemical ammonium nitrate to create an explosion to inflate airbags. But it can deteriorate over time due to heat and humidity and explode with too much force, blowing apart a metal canister designed to contain the explosion. At least 23 people have been killed worldwide and hundreds injured by the inflators. Ford says it doesn't know of any injuries in vehicles included in this recall. Dealers will replace the inflators. Ford will notify owners about the recall starting on Feb. 18, and the company has replacement parts available for dealers to order, said spokeswoman Monique Brentley. In previous Takata recalls, parts availability had been an issue. Owners can go to this Ford website and key in their vehicle identification number to see if their cars and SUVs are being recalled. The same information will be available soon at the NHTSA recall website. More than three years after the U.S. National Highway Traffic Safety Administration took over management of recalls involving Takata inflators, one third of the recalled inflators still have not been replaced, according to an annual report from the government and a court-appointed monitor. The report says 16.7 million faulty inflators out of 50 million under recall have yet to be replaced. And 10 million more inflators are scheduled to be recalled this month, including the Ford vehicles. Safety advocates said the completion rate should be far higher given the danger associated with the inflators. The recalls forced Takata of Japan to seek bankruptcy protection and sell most of its assets to pay for the fixes. The inflators grow more dangerous as they get older because ammonium nitrate deteriorates due to high humidity and cycles from hot temperatures to cold. The most dangerous inflators are in areas of the South along the Gulf of Mexico that have high humidity. Related Video:

Ringbrothers shows off Coyote-powered 1968 Mercury Cougar

We'll openly admit that not every SEMA build is our cup of tea. But this? A tastefully resto-modded 1968 Mercury Cougar with a 460-horsepower Ford Mustang V8? Yeah, this is right in our wheelhouse. Sadly, there was no in-pwerson SEMA show in 2020, so we missed out on gems like this one. SEMA or no SEMA, the aftermarket carries on, and co-owners Jim and Mike Ring of Ringbrothers (get it?) saw no reason to let their time and effort go to waste.  When they're not building wild customs (see: 1,100-horsepower 1972 AMC Javelin AMX) or more subtle showcases (such as this Cougar or their 1971 K5 Chevy Blazer build from 2018), the folks at Ringbrothers crank out factory reproduction parts, whether for old-fashioned restoration or modification purposes. While '60s muscle cars are recurring build subjects for the two, the Cougar was the first of its kind they tackled.  Keeping it in the family, Ringbrothers sourced a Ford 5.0-liter "Coyote" V8 and a 10-Speed Automatic (lifted from an F-150 Raptor, incidentally) for the build. They didn't stop with the driveline, of course. The suspension was overhauled with a little help from DSE and a set of HRE Series C1 C103 Forged 3-Piece wheels were thrown over upgraded brakes.  "We put our heart into each car we build, and this Cougar is no exception," Jim said. "The finished product is mild and classy, yet any enthusiast instantly knows it's not stock. I imagine this is what Mercury designers would have come up with if they were building the Cougar today." "While we couldn't bring the car to the SEMA Show, we hope it can be shown to the public soon," Mike said. "We had never done a Cougar before, so this was a fun build. I love working with new shapes and coming up with new ideas." There's plenty to appreciate about this Cougar apart from the mechanicals, too. The finish is Augusta Green Metallic (courtesy of BASF), which was a factory color in 1968. You may know it by another name: Highland Green. There are a few custom exterior touches, but they're quite subtle and styled to be period-correct. The interior was also restored and updated, and it's where you'll find the only thing we're not fond of: that big, fat truck shifter. Gearbox choices notwithstanding, it's a bit of an eyesore. But considering how gorgeous the rest is, we'll give it a pass.  Related Video: