1966 Mercury Comet 390 V8 Engine, Bucket Seat Interior, Amazing Paint And Body! on 2040-cars

Auto blog

Ford recalling 126,000 Fusions and Milans over wheel separation concern

Ford has announced a recall of certain Ford Fusion and Mercury Milan vehicles after an investigation by the National Highway Traffic Safety Administration. A total of 128,616 2010 and 2011 models equipped with steel wheels may have been manufactured with wheel studs that could crack and split over time. If that happens, the vehicle may experience a wheel separation.
According to The Detroit News, the company is aware of a total of 30 wheel separation incidents, one of which occurred on the front of the vehicle. Even so, no injuries have been reported as a result of the defect.
The problem apparently stems from the fact that the mounting pads on the vehicles' steel wheels may have been faulty from the factory. In addition, the wheel mounting face on rear disc brakes may not have been installed properly. Ford will inspect the rear disc face and replace them as necessary. In addition, the company will replace all of the vehicle's wheel studs free of charge. Head to the NHTSA website for more information, and click past the jump to view the full recall notice.

More than 800,000 Fords recalled for faulty Takata airbags

The Basics: Ford is recalling about 816,000 Ford, Lincoln, and Mercury vehicles built in the US for faulty passenger-side Takata airbags. The affected vehicles were all built in North America, with 654,695 recalled vehicles in the US and 161,174 vehicles in Canada. A wide variety of cars, trucks, and SUVs are affected. This is a planned expansion of an earlier recall. 2005-09 and 2012 Ford Mustang 2005-06 Ford GT 2006-09 and 2012 Ford Fusion 2007-09 Ford Ranger 2007-09 Ford Edge 2006-09 and 2012 Lincoln Zephyr and Lincoln MKZ 2007-09 Lincoln MKX 2006-09 Mercury Milan The Problem: Like every other Takata recall, the problem rests with faulty airbags that can potentially expel shrapnel, injuring or killing vehicle occupants. Millions of vehicles from dozens of automakers are affected, so don't think that Ford is alone on this one. Injuries/Deaths: Ford stated in a press release that there have been no injuries or death linked to the vehicles in this recall. All in all, 11 deaths and 180 injuries across a variety of automakers have been linked to these Takata airbags. The fix: Ford will contact owners soon, and the affected vehicles will have their airbags replaced by a dealer at no additional charge. If you own one: Wait for contact from Ford, then head to the dealer to get a replacement. If you're wondering if your vehicle is affected, go to this Ford website and enter their Vehicle Identification Number (VIN). The recall reference number is 17S01. Related Video: News Source: FordImage Credit: Associated Press Recalls Ford Lincoln Mercury Auto Repair Ownership Safety Truck Coupe Crossover SUV Sedan airbag Takata airbag recall

Ringbrothers shows off Coyote-powered 1968 Mercury Cougar

We'll openly admit that not every SEMA build is our cup of tea. But this? A tastefully resto-modded 1968 Mercury Cougar with a 460-horsepower Ford Mustang V8? Yeah, this is right in our wheelhouse. Sadly, there was no in-pwerson SEMA show in 2020, so we missed out on gems like this one. SEMA or no SEMA, the aftermarket carries on, and co-owners Jim and Mike Ring of Ringbrothers (get it?) saw no reason to let their time and effort go to waste.  When they're not building wild customs (see: 1,100-horsepower 1972 AMC Javelin AMX) or more subtle showcases (such as this Cougar or their 1971 K5 Chevy Blazer build from 2018), the folks at Ringbrothers crank out factory reproduction parts, whether for old-fashioned restoration or modification purposes. While '60s muscle cars are recurring build subjects for the two, the Cougar was the first of its kind they tackled.  Keeping it in the family, Ringbrothers sourced a Ford 5.0-liter "Coyote" V8 and a 10-Speed Automatic (lifted from an F-150 Raptor, incidentally) for the build. They didn't stop with the driveline, of course. The suspension was overhauled with a little help from DSE and a set of HRE Series C1 C103 Forged 3-Piece wheels were thrown over upgraded brakes.  "We put our heart into each car we build, and this Cougar is no exception," Jim said. "The finished product is mild and classy, yet any enthusiast instantly knows it's not stock. I imagine this is what Mercury designers would have come up with if they were building the Cougar today." "While we couldn't bring the car to the SEMA Show, we hope it can be shown to the public soon," Mike said. "We had never done a Cougar before, so this was a fun build. I love working with new shapes and coming up with new ideas." There's plenty to appreciate about this Cougar apart from the mechanicals, too. The finish is Augusta Green Metallic (courtesy of BASF), which was a factory color in 1968. You may know it by another name: Highland Green. There are a few custom exterior touches, but they're quite subtle and styled to be period-correct. The interior was also restored and updated, and it's where you'll find the only thing we're not fond of: that big, fat truck shifter. Gearbox choices notwithstanding, it's a bit of an eyesore. But considering how gorgeous the rest is, we'll give it a pass.  Related Video: