2003 Mazda Protege5 Base Hatchback 4-door 2.0l on 2040-cars

Auto blog

Chicago Auto Show page claims 2016 Mazda MX-5 Miata to produce 155 hp [UPDATE]

UPDATE: Mazda wasn't willing to confirm or deny the figures cited by the Chicago Auto Show, although we're betting the 155-horsepower figure is a bit on the low side. As for the CAS page, a Mazda spokesman told Autoblog that they "aren't sure where they got that number." The horsepower estimate has since been pulled down. Well, someone may have made a boo-boo. The Chicago Auto Show is currently hosting a page that claims the Mazda MX-5 will produce 155 horsepower, courtesy of a 2.0-liter, Skyactiv four-cylinder. If this is correct, it'd be the first time the MX-5's US power output had been revealed. The 155 hp figure would account for a 12-hp drop from that of the outgoing MX-5, though, a corresponding weight loss should still improve the power-to-weight ratio for the 2016 model. Now, the CAS page could simply be following previous reports, including one from Autoblog. As recently as October, it was being reported that the MX-5 would be powered by a 2.0-liter, Skyactiv four-cylinder, a version of which is producing 155 horsepower and 150 pound-feet of torque in the Mazda3. Naturally, we've reached out to Mazda for comment – or perhaps even confirmation – on the info from CAS, although we aren't expecting a reply until at least later this morning (darn time zones). Of course, as soon as we hear anything, we'll update this story. Related Video:

2014 Mazda6: Winter's End Update

The Winter Without End is seemingly dead. Outside my office windows, my brown and yellow lawn is fully exposed to the increasingly powerful sunshine, the morning birdsong is louder than anything until the garbage trucks start rolling, and I'm seriously considering having the summer tires put back on my personal fleet. That last one is a little scary, as I'm a firm believer in the April Snow Jinx, but you get the idea.
The long-term Mazda6 has also long since left my driveway. Looking back on my notes from the time it was in my charge, however, I see all remarks are dominated by one highlighted section at the top: "worst winter drive of all time." I hardly need the reminder, to be honest. Here's what happened.
When the Mazda showed up at my door, we'd already fitted the thing with its new winter rubber: Bridgestone Blizzaks. Plunking down for dedicated snow tires was a near necessity this year - as it almost always is in Michigan. We didn't see much reprieve from snow-choked, iced over roads here in Ann Arbor, and the knobbier rubber proved invaluable in getting me out of my house time and again.

50 engineers kept the rotary alive at Mazda for 8 years

The Mazda RX-Vision concept is one of the standouts at this year's Tokyo Motor Show thanks to a drop-dead gorgeous design and a revival of the Wankel engine. The fact that the rotary is still in development at Mazda is thanks to a dedicated group of 50 engineers. According to Automotive News, their dream for the last eight years has been to bring this storied engine design back to the street. It won't be easy. Because of its design, the rotary suffers from poor fuel economy and high emissions. Making the challenge even harder, Mazda reportedly only gives them a small budget, but they continue to chip away at the problem. "These 50 engineers want to develop the rotary engine, therefore they joined Mazda," company research and development boss Kiyoshi Fujiwara told AN. "If I stop the rotary engine, probably they want to leave." For the Skyactiv-R under the RX-Vision's svelte hood, the team reportedly started from the 16X rotary project. Dating back to 2007, that 1.6-liter engine was supposed to improve torque and fuel economy thanks in part to direct injection. After additional development, insiders even suggested that the engineers might have finally solved the powerplant's issues. However, Mazda never put the mill into production, and the RX-8 remains the company's last Wankel-powered model to be offered in showrooms. "We have a dream that one day, this design with a rotary engine will achieve a level that customers will accept," CEO Masamichi Kogai said to AN. Mazda is quite clear that the RX-Vision might never go on sale without a suitable rotary. Although if it does see production, the coupe would likely use a stiffened version of the Miata's chassis, AN reports. Before anyone can place an order, these 50 determined engineers still have a lot of work ahead of them. Related Video: