1961 Jeep Cj 6 on 2040-cars

Auto blog

Four Wheeler crowns Ultimate Factory 4x4... who wins?

Nearly every automaker doing business in the SUV or pickup truck segments offers a package designed to improve the off-road capabilities of its wares. But, of course, not all such factory kits are created equal. How, then, to separate the wheat from the chaff? Gather each of them up and put them through their paces, naturally.
The folks from Four Wheeler and PickupTrucks.com joined forces to run just such a comparison test, with the winner named the Ultimate Factory 4x4. A total of seven vehicles showed up to the fight: the 2012 Ford F-150 SVT Raptor, 2013 Jeep Wrangler Rubicon, 2012 Nissan Frontier PRO-4X and Xterra PRO-4X, 2012 Ram Power Wagon, and 2012 Toyota 4Runner Trail and Tacoma TRD T|X Baja Series.
With the contestants in place, the whole crew put each vehicle through a battery of tests that included skidpad and acceleration measurements, a hillclimb, a rocky stairstep course and a rock garden. Considering the nature of the beasts, on-road ride and comfort were not part of the routine.

Chrysler axes old V6s, goes all-Pentastar

Old technology has a way of lingering on, particularly at Chrysler headquarters in Auburn Hills. So while the Pentastar V6 has replaced the older engine architecture in just about every application, it still soldiered on in some export markets. But the introduction of a new 3.0-liter Pentastar V6, produced in Michigan and meant only for the Chinese market, has put the final nail in the old engine's coffin.
Fitted into the 2014 Jeep Grand Cherokee and Jeep Wrangler just introduced to China at the Chengdu Motor Show, the downsized six uses the same architecture as the larger 3.6-liter Pentastar V6. But because of its 2,997cc capacity, it can be exported to China without the increased duty the 3.6-liter or even 3.2-liter Pentastar engines would incur. The 3.0-liter V6 develops 230 horsepower at 6,350 rpm and 210 pound-feet at 4,400 rpm.
Admittedly, it's unlikely, but even though the engine was said to be created solely to undercut tax thresholds in China and Europe, the 3.0-liter Pentastar has recently surfaced in rumors of an application here: as the boosted heart of a potential Cherokee SRT with anywhere from 375 to 410 hp.

Chrysler says its 8-speed transmissions will save 700 million gallons

Chrysler Group's TorqueFlite eight-speed transmission could be earning some serious green bragging rights if the company's projections are correct. The recently widely proliferated automatic gearbox, which is now in more than a million vehicles around the world, is poised to save drivers an estimated 700+ million gallons of fuel over the vehicles' lifetimes (an expected cost savings of $2.5 billion). In addition, Chrysler expects a reduction in CO2 emissions by more than six million metric tons. According to Chrysler, and depending on the vehicle, the TorqueFlite can improve fuel economy. The TorqueFlite autobox features particularly close ratios from fifth to eighth gear (see the press release below for the specific numbers), and uses low-viscosity fluid that doesn't need to be replaced. Transmission software adapts to the driving situation to optimize efficiency based on driver behavior, temperature, grade, stability control, and longitudinal and lateral acceleration. The TorqueFlite is capable of handling a variety of duties. As evidenced by the wide range of vehicles Chrysler Group has seen fit to equip with the eight-speed transmission, the TorqueFlite is capable of handling a variety of duties. Since its 2012 introduction, the TorqueFlite has gone from performing cog-swapping duties in Dodge Charger and Chrysler 300 models equipped with the 3.6-liter Pentastar V6 to changing gears in vehicles such as the Pentastar- and Hemi-powered Dodge Durango, Jeep Grand Cherokee and even the Ram 1500 EcoDiesel. For the 2015 model year, the eight-speed is finding its way into even more vehicles with the addition of a third version. In addition to the American-made TorqueFlite 845RE and 8HP70, the new 8HP90 will be manufactured in Saarbrucken, Germany. The 8HP90 is designed for higher torque loads, making it ideal for high-performance vehicles like the 2015 Dodge Challenger SRT Hellcat. The already-in-use 8HP70 will expand its duties to be used in 2015 Hemi models such as the Dodge Charger, Challenger, and Challenger SRT8. You can see the list of those benchmarks in Chrysler's press release below.