1996 Infiniti Q45 Base Sedan 4-door 4.5l on 2040-cars

Auto blog

A look inside Infiniti's variable-compression engine

We're sympathetic to anyone who had trouble understanding what's going on with Infiniti's new variable-compression engine. While we got a full tech briefing on the novel VC-Turbo back in August, the visual aids were lacking. The cutaway engine Infiniti brought to the Paris show fixes all of that. You can thank the little green and pink lines on the cutaway for making the whole idea a little more clear. Click through the gallery to see two lines – one green and one pink – that represent the different strokes allowing for different compression ratios. Remember, the compression ratio is the amount of volume in the cylinder on intake compared to the amount at the end of the compression stroke. Leave more room at the end and you lower that ratio. The length of the stroke doesn't change with this system, but where it sits along the cylinder does. Hence those two lines. The variable compression ratio allows this new turbocharged engine to maximize fuel economy when the turbo isn't needed by raising the compression ratio. It will see its first use in the next Infiniti QX50 crossover, previewed by the QX Sport Inspiration concept that's also on display in Paris, and has performance targets of 268 horsepower and 288 pound-feet of torque. After, it will migrate to other Infiniti and Nissan vehicles, with transverse front-drive-based applications first in line. Eventually, it's likely to completely replace Nissan's corporate 3.5-liter V6. We'll be poking around the engine a little more in Paris today to try and get some more info. For now, enjoy those cutaway images and those friendly little lines. Featured Gallery Infiniti VC-Turbo engine cutaway View 14 Photos Paris Motor Show Infiniti Nissan Technology Emerging Technologies engine 2016 paris motor show

The yin and yang of the 2017 Infiniti Q50 Red Sport 400

When we first drove the Q50 Red Sport 400, Infiniti had the car out at a prepared slalom-and-cone course in a large, open parking lot. The car was stacked up against another Q50 without the Direct Adaptive Steer steer-by-wire system, and the course was designed to show that the DAS-equipped Red Sport 400 (it's a $1,000 option) required less steering input to master the same course. With all due respect to Infiniti, which is invested in this unfortunate system and has been working hard to revise it, the comparison doesn't make a lot of sense. The non-DAS Red Sport 400 has a steering ratio of 15:1 in RWD and 16.7:1 in AWD forms. The DAS system can vary between 12:1 and 32.9:1 in RWD and 11.8:1 to 32.3:1 in AWD flavors. At its extremes, the DAS system's ratio is vastly different than the fixed-ratio cars. So sure, with a super-quick steering ratio available, the DAS driver's going to do less work. It's all in the gearing. Does this mean it's better, that the steering feel is more natural, that it's easier to hustle quickly? The amount the driver saws at the wheel isn't an indication of that, necessarily. After a few days in a rear-drive Red Sport 400, I'm saying that the spooky disconnection between the driver and the front wheels would be a severe deficit to a driver on a real autocross course. It's not like the DAS system is choosing bad ratios within its range, it's just not supplying the feedback to make it enjoyable. Knowing what your front tires are up to is critical. I can hear you saying right now, "But what Q50 Red Sport 400 owners are going to autocross their cars?" Sure, but it was just a means to an end: showing off the DAS in a good light. And in that case, it probably did. The thing is, in isolation, not back-to-back with a non-DAS car with a slow steering ratio, the DAS system has the same issues it's always had: It simply doesn't feel natural. It doesn't feel intuitive. There doesn't seem to be any real advantage over a slightly quicker rack. I don't hear about people making buying decisions based on how much work they have to do sawing at the wheel, do you? So, that's one side of the Q50 coin – one that's hard to ignore if you're an enthusiast and steering feel is an important connection between you and the vehicle you just dropped a large hunk of change on, and will be spending a lot of your time in. The other is that there's a really compelling reason to drive a Red Sport 400: The 3.0-liter, twin-turbocharged V6 is a monster.

Daimler and Nissan to build luxury cars at new plant in Mexico

A few years back, when Daimler was looking for a partner to spread the cost of development of small cars, it agreed to collaborate with Nissan on future products, such as vehicle platforms and drivetrains. The latest development in the collaboration concerns the assembly of small luxury cars for Infiniti and Mercedes-Benz at a Nissan plant in Mexico, two unnamed sources told Reuters.
The plant in question, Aguascalientes, is a $2 billion project that will open later this year next to an existing Nissan factory. The upcoming Infiniti Q30 four-door hatchback is expected to be built there, possibly alongside the Mercedes GLA-Class, which is one of several candidates Mercedes is considering to build at this facility, Reuters reports. The GLA will debut at the Frankfurt Motor Show this month, and initial production of the model will take place in Germany. The Q30 could follow a similar path, with assembly starting at Nissan's Sunderland plant in the UK, and then expanding to Aguascalientes later on.
The underlying platform of the Q30 and GLA, codenamed New Generation Compact Car (NGCC), was developed by Daimler. The Q30 would be the first Infiniti produced under the automakers' agreement. Last year, Nissan agreed to make engines that would find their way into Mercedes and Infiniti vehicles.