2012 Honda Odyssey Ex Mini Passenger Van 4-door 3.5l on 2040-cars

Auto blog

It turns out Takata isn't willing to expand airbag recall nationally after all

There have been "approximately 0.000006 failures per air bag deployment, which is far below the failure rate" of most recalls, Takata claims. Takata has seemingly made an about face following reports that it would expand its regional airbag recall into a nationwide repair effort, issuing a scathing, four-page letter rebutting allegations by the National Highway Traffic Safety Administration and its Office of Defects while simultaneously attacking the government's handling of the situation. The Japanese supplier claims in its letter that the "currently available, reliable information does not support a nationwide determination of a safety defect," arguing that there were "approximately 0.000006 failures per air bag deployment, which is far below the failure rate in the vast majority of the thousands of recalls," The Detroit News reports. Takata then breaks down the two specific incidents mentioned in NHTSA's original recall request letter, a 2005 Honda Accord and 2007 Ford Mustang. Referencing the two crashes, NHTSA Administrator David Friedman said last month "one incident is an anomaly, but two are a trend." The supplier, though, argues the Honda issue is already being covered by that company's soon-to-be-national recall (more on that in a moment). The company then goes on to point out that neither Takata nor NHTSA has been able to analyze the Mustang's airbag inflator, saying that such a lack of examination meant there was "no way to ascertain what actually occurred during the incident, whether any inflator ruptured, and whether any inflator rupture that may have occurred was related to the incidents that led to the current regional campaigns." Takata alleges that NHTSA has disobeyed its own statutes. Takata also took the opportunity to take a few swipes at NHTSA's behavior during the airbag scandal, saying it was "very surprised to receive" a recall request letter because the ODI had yet to even receive the company's responses to a pair of special orders. It also alleged that NHTSA was disobeying its own statute, which says only manufacturers of vehicles and replacement equipment can "decide in good faith whether their products contain a safety related defect," and that the government can only "issue an initial decision that a safety-related defect exists" to those same entities.

2015 Acura NSX burns to the ground at the 'Ring [w/video]

Assuming all goes to plan, automakers test their vehicles to the breaking point in the months and years leading up to that vehicle's actual release into the public. Which is good, because it's much better for a car to break in glorious fashion in the hands of the company that produces it than in the driveway of an owner who just spent their hard-earned cash to get it. Such was the case with this production-guise Acura NSX prototype that we saw running around the Nurburgring just the other day. We can't be 100-percent certain, but the burned-out carcass is wearing the same number plate as the car that was spotted earlier, so it's likely the very same NSX. We have no idea what was the cause of the blaze that turned this Acura into the car-b-q you see pictured above, but our spy shooters on the ground in Germany say it was not involved in any collision, having caught on fire all on its own with engineers behind the wheel. The good news is that nobody was hurt, though the car is quite clearly a complete loss. We're sure there's another ready to to test in the burned car's place... just as soon as the engineers at Honda figure out exactly what went wrong. Have a look at the smoldering aftermath up above, and feel free to scroll down below to see a video of the car in much better circumstances.

Honda working with new supplier Autoliv for Takata inflator recall

Takata is fighting against US regulators over whether to expand its airbag inflator recall nationwide, but the affected automakers are continuing to broaden their own campaigns to get these vehicles fixed. Honda is the first company to take the bold move of partnering with another supplier for its replacement parts. It just announced plans to work with Autoliv to create components for models needing repaired in the US. "The agreement is made in order to meet the expanded supply of inflators needed by Honda and is subject to definitive documentation," Autoliv said in a statement. The company plans to add the extra capacity for these replacement parts at its existing factories, and deliveries are expected to begin in six months. The decision to switch suppliers was quite surprising because the choice was largely considered impractical previously. Automakers believed that changing manufacturers could take as long as a year or more to implement. However, Autoliv apparently found a way to accelerate that. According to Reuters, Honda said at a hearing in the House of Representatives on December 3 (pictured above) that it was in talks with Autoliv and another supplier called Daicel about building more inflators. The extra parts are sure to come in handy for Honda, as it is now officially expanding its driver side inflator recall nationwide. Although, that that option was already available to any concerned drivers who asked for the remedy. Even with added capacity, Takata had estimated it would take two years to manufacturer enough replacements to fix all of the affected vehicles from all of the automakers. Scroll down to read Autoliv's statement on its new role. Autoliv to supply replacement airbag inflators to be used by Honda (Stockholm, December 3, 2014) – – – Autoliv, Inc. (NYSE: ALV, and SSE: ALIV sdb), the worldwide leader in automotive safety, will supply replacement airbag inflators to be used by Honda Motor Company in support of the ongoing field action initiatives in the United States. The agreement is made in order to meet the expanded supply of inflators needed by Honda and is subject to definitive documentation. In order to be able to meet increased demand, Autoliv will build additional inflator capacity in its existing manufacturing facilities. Deliveries are estimated to commence after a period of about six months from today.