Certified 2013 Gmc Yukon Slt on 2040-cars

Auto blog

Torque time | 2017 GMC Sierra HD First Drive

It's not the truck that counts, it's how you use it. It's the heavy stuff you fit in its bed or the extremely heavy stuff that gets hooked up to the tow hitch. The ATV, the Jet Skis, the trailer with more square footage than a Greenwich Village apartment. Perhaps you need to get Seabiscuit or, uh, Mr. Ed to wherever they need to gallop next. In our case, there's a pair of very serious-looking snowmobiles perched atop the bed of a GMC Sierra. They spread out as wide as the extended tow mirrors, and their back halves are dangling precariously beyond the truck. Sterling Archer would be giddy; I'm a little nervous. But only because canyon roads and wide vehicles with a high center of gravity go together like peas and custard. The added weight is no sweat at all. That's because this is the 2017 GMC Sierra HD Denali, a truck with the sort of enhanced power, torque, suspension, and stopping capability expected of a heavy-duty pickup. And for this year, the power and torque get a serious bump courtesy of a new 6.6-liter Duramax turbodiesel engine reengineered from almost the ground up with 90 percent new parts. It's quieter and more efficient and it emits less, while most importantly producing 445 horsepower and 910 pound-feet of torque. That's up from 397 and 765, respectively. Chevy fans will note that the same engine is also available in the updated 2017 Silverado HD. Now, for those keeping score at home, that horsepower is best-in-class but the torque number still falls short of the new Ford Super Duty and its Power Stroke diesel V8's 925 lb-ft. Aw shucks. For the record, GM's engineers didn't seem too concerned that they weren't able to eke out an extra 16 torques just to say they're No. 1. "We wanted to first meet emissions and then deliver the maximum horsepower and torque we could, and deliver it over the widest usability range possible," said chief engineer Eric Stanczak. And let's be honest here, 910 pound-feet is herculean, and once again, a jump of 145 lb-ft. Or one Subaru Impreza's worth. Or 110 more than the best Ram can do on a 2500, and its Cummins turbodiesel's 800 pound-feet was eye-popping not too long ago. (The Ram 3500 maxes out at 900 lb-ft with the right transmission.) Ah, but here's the rub. That Cummins-equipped Ram 2500 can still tow more weight according to SAE-compliant measurements – 17,510 pounds for a Ram crew cab with a short bed versus 13,000 in the similar Sierra 2500. The Ford F-250 can manage 15,000.

2019 GMC Sierra carbon fiber bed: How it's made

FORT WAYNE, Ind. — The redesigned 2019 GMC Sierra has some pretty nifty features, and the one that has had the most attention is the MultiPro flipping and folding tailgate. But the Sierra also features the first-of-its-kind carbon fiber truck bed. It's interesting, of course, for its capabilities, such as being 62 pounds lighter than the all-steel box. It even adds more cargo volume since the material can be assembled and shaped differently from steel. As it turns out, the assembly process is cool, too, which we learned when GMC invited us to see the beds being made. Every GMC carbon fiber bed starts out as perfectly flat sheets of thermoplastic carbon fiber. The sheets consist of a mix of fibers and resins, a bit like the molded carbon fiber parts Lamborghini uses. The sheets are manufactured by Japanese company Teijin, which collaborated with GMC to develop the bed. They're all delivered to Continental Structural Plastics (CSP) in Fort Wayne, Ind., for construction into the actual bed. The company, a subsidiary of Teijin, makes a wide variety of composite and plastic parts for the car industry, including body panels for the C7 Chevy Corvette. The rectangular sheets are cut to shape and stacked up at a giant stamping press. Robots pick up sheets and slide them onto a conveyor that goes into a large oven. The heat softens the parts so they can be stamped. The large primary bed parts such as the base are stamped by CSP's enormous 3,600-ton press, and the smaller ones go through a 1,000-ton press. Each press can do different parts using different stamping dies, and CSP switches between dies to produce different batches of parts. After stamping, the parts roll out mostly ready for assembly, but there are rough edges that are trimmed off by water-jet cutters. These cutting machines also create holes for fasteners and for parts such as tie-down hooks and lights. The stamping process also provides the carbon fiber bed with a unique Easter egg. On the bottom of the base of the bed, there are two words: "Connors Way." This is a tribute to Tim Connors, who was the chief engineer of manufacturing at GM and a strong proponent of the carbon fiber bed. He was tragically killed in a motorcycle crash a few years ago. The words were added to honor him, and they were fortunately approved for production. There are some components to the bed that aren't stamped from the flat sheets of material.

Inevitable GMC Canyon Denali spotted testing

Practically every other model in the GMC lineup already offers a more luxurious Denali option, so why not extend that to the Canyon midsize pickup? It's hardly a surprise to see the brand doing just that, especially since the standard model seems to be proving quite a success. This Canyon was recently spied testing wearing camouflage over its front end. The truck still needs to breathe, though, and the opening in the obfuscation makes it quite easy to spot the Denali's chrome mesh grille, rather than the horizontal slats of the standard model. Also, just peeking out of the bottom part of the masking is the lower air intake, which appears to be completely lined in chrome now. At the sides and rear, the styling is identical to the current look of the pickup, at least for this prototype. While our spies didn't snap any shots of the interior, it seems safe to anticipate the usual Denali upgrades there, including better materials and additional tech features. Of course, expect a bump in price at the same time to pay for the improvements.