2008 Gmc on 2040-cars
Houston, Texas, United States
Vehicle Title:Clear
For Sale By:Dealer
Engine:6.2L 6199CC 378Cu. In. V8 GAS OHV Naturally Aspirated
Body Type:Sport Utility
Fuel Type:GAS
Make: GMC
Model: Yukon XL 1500
Trim: Denali Sport Utility 4-Door
Disability Equipped: No
Doors: 4
Drive Type: AWD
Drivetrain: All Wheel Drive
Mileage: 81,795
Sub Model: AWD w/ Navigation/Sunroof/DVD/Buckets/3rd Row/20s
Number of Cylinders: 8
Exterior Color: Black
Interior Color: Tan
GMC Yukon for Sale
2011 gmc(US $45,014.00)
2011 gmc(US $38,071.00)
2009 gmc(US $32,971.00)
Gps navigation leather moonroof dvd 4x4 quad buckets third row seat new tires(US $13,995.00)
Slt 5.3lone owner , leather, back up camera,running board, fog lights very nice
Sle suv 5.3l locking/limited slip differential rear wheel drive tow hitch abs
Auto Services in Texas
Z`s Auto & Muffler No 5 ★★★★★
Wright Touch Mobile Oil & Lube ★★★★★
Worwind Automotive Repair ★★★★★
V T Auto Repair ★★★★★
Tyler Ford ★★★★★
Triple A Autosale ★★★★★
Auto blog
NHTSA investigates 1.7 million GM SUVs for windshield wiper failures
Tue, Nov 6 2018WASHINGTON - The U.S. National Highway Traffic Safety Administration (NHTSA) said on Tuesday it is investigating whether General Motors should recall an additional 1.7 million sport utility vehicles due to an issue with windshield wiper failures. GM in August 2016 recalled 367,800 2013 GMC Terrain and Chevrolet Equinox SUVs in the United States to address the problem. But after receiving 249 complaints about similar problems, the federal agency said it is probing whether the recall should be expanded to include an additional 1.7 million vehicles from the 2010-2016 model years. The automaker said it is cooperating with the NHTSA review. GM said it recalled the 2013 GMC Terrain and Chevrolet Equinox SUVs "because warranty data showed a higher-than-expected failure rate," adding it has continued to monitor field data on other model years of those vehicles. GM noted that no crashes or injuries related to the issue have been reported. The Detroit-based automaker said the recalls were prompted after a GM Canada brand quality manager reported a potential safety issue relating to reports of windshield wiper failures in Canada through GM's "Speak Up For Safety," program in late 2015. The data showed significantly higher field incidents in parts of Canada, which prompted a June 2016 recall there. Over the next two months, a higher number of U.S. reports prompted a U.S. recall, the company added. In the 2016 recall, GM said the front-wiper module would be replaced with a module that has a water deflector and, if needed, dealers would fill the water management hole and drill a new small hole in a different location.(Reporting by David Shepardson, editing by G Crosse)Related Video: Government/Legal Recalls Chevrolet GM GMC SUV
2019 GMC Sierra carbon fiber bed: How it's made
Fri, Apr 26 2019FORT WAYNE, Ind. — The redesigned 2019 GMC Sierra has some pretty nifty features, and the one that has had the most attention is the MultiPro flipping and folding tailgate. But the Sierra also features the first-of-its-kind carbon fiber truck bed. It's interesting, of course, for its capabilities, such as being 62 pounds lighter than the all-steel box. It even adds more cargo volume since the material can be assembled and shaped differently from steel. As it turns out, the assembly process is cool, too, which we learned when GMC invited us to see the beds being made. Every GMC carbon fiber bed starts out as perfectly flat sheets of thermoplastic carbon fiber. The sheets consist of a mix of fibers and resins, a bit like the molded carbon fiber parts Lamborghini uses. The sheets are manufactured by Japanese company Teijin, which collaborated with GMC to develop the bed. They're all delivered to Continental Structural Plastics (CSP) in Fort Wayne, Ind., for construction into the actual bed. The company, a subsidiary of Teijin, makes a wide variety of composite and plastic parts for the car industry, including body panels for the C7 Chevy Corvette. The rectangular sheets are cut to shape and stacked up at a giant stamping press. Robots pick up sheets and slide them onto a conveyor that goes into a large oven. The heat softens the parts so they can be stamped. The large primary bed parts such as the base are stamped by CSP's enormous 3,600-ton press, and the smaller ones go through a 1,000-ton press. Each press can do different parts using different stamping dies, and CSP switches between dies to produce different batches of parts. After stamping, the parts roll out mostly ready for assembly, but there are rough edges that are trimmed off by water-jet cutters. These cutting machines also create holes for fasteners and for parts such as tie-down hooks and lights. The stamping process also provides the carbon fiber bed with a unique Easter egg. On the bottom of the base of the bed, there are two words: "Connors Way." This is a tribute to Tim Connors, who was the chief engineer of manufacturing at GM and a strong proponent of the carbon fiber bed. He was tragically killed in a motorcycle crash a few years ago. The words were added to honor him, and they were fortunately approved for production. There are some components to the bed that aren't stamped from the flat sheets of material.
GMC Envoy could be returning as GM files for 'Envoy' trademark
Thu, Dec 27 2018The GMC Envoy could be on its way back, if a recent GM trademark filing is any indication of the future. To be exact, GM's trademark filing is for the name "Envoy," and is applicable to "motor vehicles, namely, sport utility vehicles, engines therefor and structural parts thereof." A victim of the recession and high gas prices, the original Envoy – related to the Blazer, and more recently the TrailBlazer and similar GM SUVs – was discontinued after the 2009 model year. In today's SUV-happy market of low gas prices, unearthing the somewhat familiar Envoy name makes a certain amount of sense. As soon as gas prices start trending in the other direction, we'll all be saying the opposite, though. What this SUV will take shape as is the big question now. With the Chevrolet Blazer well and truly on its way, there's every reason for a GMC version of Chevy's stylish new crossover sporting the Envoy name. Another, less likely, possibility is a Traverse-sized vehicle to slot between the shorter Acadia (10 inches shorter than the Chevy Traverse) and the body-on-frame Yukon. GM could come out of left field and make the Envoy a Buick too. It fits the bill with the "En" beginning, and Buick undoubtedly has crossovers in the works. We think that's even more unlikely, but it's important to remember that we're still in the speculation phase. Soon we'll drive Chevy's new Blazer, and perhaps have more news then. Check in next week for that. Related video: