2007 Gmc Yukon Denali Clean 76k Dvd, Nav, Power Running Boards, Rear Buckets on 2040-cars

Auto blog

Chevy's 6.6-liter Duramax is pretty much all new

To say there's a heated battle in heavy-duty pickups is an understatement, with Chevrolet, Ford, and Ram constantly trading blows of increased torque, horsepower, and towing capacity. The latest salvo is the revised, more powerful turbo diesel 6.6-liter Duramax V8 in the 2017 Chevy Silverado. It has 910 pound-feet of torque, an increase of 145, putting it nearly level with the Ford Super Duty. Here's a closer look at where those gains come from. How exactly did Chevrolet add all that torque plus 48 horsepower? The automaker essentially took a fine-tooth comb to the entire engine. Chevy says it changed 90 percent of the V8, and the cumulative effect of those small changes adds up to big increases. As you might guess, the turbocharger is updated. The larger unit features electric actuation of the variable nozzle turbine (VNT), and what Chevy calls a double axle cartridge mechanism that separates the VNT moving parts from the housing. That helps with heat performance as well, with a claim that the exhaust side of the turbo can run continuously up to 1,436 degrees Fahrenheit. Helping that cause are six exhaust gaskets made of Inconel - an nickel alloy that contains chromium and iron – and upgraded stainless steel for the exhaust manifold. Despite having the same cast iron cylinder block, albeit with some minor enhancements, the engine has new cylinder heads, pistons, piston pins, connecting rods, and crankshaft, which have all been upgraded to handle 20 percent higher cylinder pressures. Alongside the increase in pressure, Chevrolet also increased the cylinder head's structure with a honeycomb design. The pattern features high-strength aluminum with dual layer water jackets that not only improve strength, but also optimize water flow for better cooling. For 2017, the cylinder head also benefits from integrated plenum that aids the engine in getting more air under heavy loads. The cylinder head isn't the only component to get a minor update, as the pistons have a larger diameter pin for improved oil flow. The same detailed improvements has been bestowed to the humble connecting rods (second in our hearts only to the inanimate carbon rod). The new design has the bolts oriented roughly 45-degrees to the rod instead of parallel. The angle split design, as it's called allows for easier passage through the cylinder.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

2019 GMC Sierra Denali MultiPro tailgate and CarbonPro bed explained

When the 2019 Chevy Silverado debuted at the Detroit Auto Show in January, GM's Mark Reuss promised that the new 2019 GMC Sierra would have some significantly different styling and features than its corporate sibling. Previously, the Sierra has been little more than a Silverado with new front and rear fascias and some extra chrome inside and out. Well, Reuss was right. In addition to new sheetmetal, the Sierra exclusively gets the slick MultiPro tailgate and CarbonPro carbon-fiber bed box The tailgate really is trick. At the debut, GMC had multiple demonstrations, with engineers walking us through all six different configurations. Like all Sierra tailgates, the MultiPro version uses an aluminum skin to reduce weight. It's easy to tell which tailgate is which, as the MultiPro has a distinct cutout in the middle where it can fold down or extend. It can be used to extend the bed, drop to allow easier access, provide a sort of workbench, or be used as a step to help get into the bed. Yes, there's even a handle. Ford who? The step itself can support up to 375 pounds, 75 pounds more than Ford's similar tailgate step. This tailgate really is unique to the Sierra and is standard on SLT and Denali models. That said, the power-operated tailgate from the Silverado won't be coming to the GMC. Chevy gets its own exclusive, too. The Sierra's other big exclusive is the carbon-fiber reinforced plastic bed box. CFRP replaces steel inside the bed though not on the fenders. The bed uses four pieces; one for the bottom, one in the back and two along the sides. This isn't a CFRP. There is no steel hiding underneath these panels. Just take a peek underneath. The bed is a composite that uses 1-inch carbon-fiber threads, not a weave. Sheets of CFRP are molded and quenched — a process where the plastic coagulates and solidifies, locking in the carbon fiber — in just 60 seconds. That allows GMC's supplier to crank out these much more quickly. The finish looks like black fiberglass, though an engineer said that this wasn't the final production version. The final model will have different textures in order to improve grip and keep things from sliding around. GMC is touting the material's dent and corrosion resistance, though it remains to be seen how well it holds up to cracking. A video at the reveal showed people going after it with hammers and cinder blocks, but in-person demonstrations weren't available.