2007 Gmc Yukon Denali Awd Black On Black Low Miles Loaded Sharp on 2040-cars

Auto blog

2016 GMC Terrain Denali Quick Spin

Here's a bewildering statistic – General Motors sold over 347,000 GMC Terrain and Chevrolet Equinox crossovers in 2014, making the Theta platform twins the best selling vehicles in their segment. GM sold more Equinox/Terrain crossovers than Honda did CR-Vs, Ford did Escapes, and Toyota did RAV4s. After a week behind the wheel of the 2016 Terrain Denali, we can't fathom why GMC's entry, which accounts for nearly a full third of GM's annual small CUV sales, has been so popular. An inefficient engine, cheap interior plastics, uncomfortable seats, a shortage of technology, and a high price left us questioning why anyone would order this Denali over a Titanium-trim Ford Escape, a Jeep Cherokee Limited, or a Hyundai Santa Fe Sport with the Unlimited Package. Driving Notes While looks are subjective, we'd posit that GMC didn't go far enough with its 2016 mid-cycle refresh. New accents on the front bumper, a tweaked grille surround, and LED running lights round out the changes up front, while the rear gets a slightly different bumper. GMC claims there's a new hood, although we challenge you to pick out the differences – here are the official galleries for the 2013 and 2016, if you'd like to try. GMC missed a tremendous opportunity here. New headlights, some restyled taillights, and tweaked mirrors would have given the impression of a more significant refresh. As it stands, these changes don't add up to much. GMC also claims it made changes in the cabin, adding a "revised instrument panel center stack." Aside from the missing CD slot, which has been replaced with an oddly shaped and not terribly useful shelf, it's hard to spot much of a difference. The Terrain Denali's cabin materials feel cheap. You'll be spending at least $35,000 to park one of these in your driveway, but aside from the leather-and-faux-wood steering wheel, no material feels worthy of that price tag inside. The lower dash plastics are hard and scratchy, the center stack feels hollow and creaks when pressed on, and the too-small shade over the seven-inch display feels flimsy. The upper dash is covered in a cheap-feeling, leather-like material that looks unchanged from when the Terrain Denali debuted back in model year 2013. These materials don't make sense in a vehicle that, as tested, exceeded $41,000. The most egregious thing about the refreshed Terrain is the lack of content.

2019 GMC Sierra carbon fiber bed: How it's made

FORT WAYNE, Ind. — The redesigned 2019 GMC Sierra has some pretty nifty features, and the one that has had the most attention is the MultiPro flipping and folding tailgate. But the Sierra also features the first-of-its-kind carbon fiber truck bed. It's interesting, of course, for its capabilities, such as being 62 pounds lighter than the all-steel box. It even adds more cargo volume since the material can be assembled and shaped differently from steel. As it turns out, the assembly process is cool, too, which we learned when GMC invited us to see the beds being made. Every GMC carbon fiber bed starts out as perfectly flat sheets of thermoplastic carbon fiber. The sheets consist of a mix of fibers and resins, a bit like the molded carbon fiber parts Lamborghini uses. The sheets are manufactured by Japanese company Teijin, which collaborated with GMC to develop the bed. They're all delivered to Continental Structural Plastics (CSP) in Fort Wayne, Ind., for construction into the actual bed. The company, a subsidiary of Teijin, makes a wide variety of composite and plastic parts for the car industry, including body panels for the C7 Chevy Corvette. The rectangular sheets are cut to shape and stacked up at a giant stamping press. Robots pick up sheets and slide them onto a conveyor that goes into a large oven. The heat softens the parts so they can be stamped. The large primary bed parts such as the base are stamped by CSP's enormous 3,600-ton press, and the smaller ones go through a 1,000-ton press. Each press can do different parts using different stamping dies, and CSP switches between dies to produce different batches of parts. After stamping, the parts roll out mostly ready for assembly, but there are rough edges that are trimmed off by water-jet cutters. These cutting machines also create holes for fasteners and for parts such as tie-down hooks and lights. The stamping process also provides the carbon fiber bed with a unique Easter egg. On the bottom of the base of the bed, there are two words: "Connors Way." This is a tribute to Tim Connors, who was the chief engineer of manufacturing at GM and a strong proponent of the carbon fiber bed. He was tragically killed in a motorcycle crash a few years ago. The words were added to honor him, and they were fortunately approved for production. There are some components to the bed that aren't stamped from the flat sheets of material.

Chevy Colorado, GMC Canyon midsize pickup trucks to get diesel engines

The market for midsize pickup trucks has all but been abandoned in the US, but General Motors is about to shake the market up with the all-new (to the US) Chevrolet Colorado and GMC Canyon. Launching next year, GM already told us that its new trucks would be a "fuel-efficient alternative" to fullsize trucks, and aside from the smaller size, Automotive News says that these trucks will accomplish this with a diesel engine.
According to the AN report, the next-gen Colorado and Canyon will offer a small, four-cylinder Duramax turbo diesel with a displacement of either 2.5 or 2.8 liters - both engines are currently used in this truck for other markets. This would allow GM to join the Cummins-powered Nissan Titan and Ram 1500 EcoDiesel as the only non-HD trucks in the US to offer diesel. The article goes on to say that the diesel versions of the Colorado and Canyon would launch about a year after the trucks go into production in fall of 2014.