2007 Gmc Yukon 2wd 4dr 1500 Sle on 2040-cars

Auto blog

GM recalling 8.4M cars, 8.2M related to ignition problems

General Motors today announced a truly massive recall covering some 8.4 million vehicles in North America. Most significantly, 8.2 million examples of the affected vehicles are being called back due to "unintended ignition key rotation," though GM spokesperson Alan Adler tells Autoblog that this issue is not like the infamous Chevy Cobalt ignition switch fiasco.
For the sake of perspective, translated to US population, this total recall figure would equal a car for each resident of New Hampshire, Rhode Island, Montana, Delaware, South Dakota, Alaska, North Dakota, the District of Columbia, Vermont and Wyoming. Combined. Here's how it all breaks down:
7,610,862 vehicles in North America being recalled for unintended ignition key rotation. 6,805,679 are in the United States.

GMC Hummer EV will weigh 9,046 pounds

In the 2000s, Hummer's unique breed of off-roaders summoned a dark cloud of disapproval from environmentalists because they were gas-guzzling SUVs with mammoth dimensions. GMC's born-again Hummer EV will escape the gas guzzler label by running solely on electricity, but it will be even bigger and much heavier than its predecessors. Enthusiast site GM-Trucks reported the Hummer EV will tip the scale at 9,046 pounds (4,103 kilos if you're outside of the United States) in its quickest configuration, and a GMC spokesperson told Autoblog that figure is accurate. For context, the H1 Alpha released for 2006 (and often considered the ultimate Hummer) weighed 8,113 pounds, the H2 checked in at 6,614 pounds with the 6.2-liter V8, and the H3 was comparatively light at 4,600 pounds. When it lands, the Hummer EV will be one of the heaviest new cars sold in the United States. Part of its plumpness can be attributed to its colossal dimensions; it measures 216.8 inches long, 86.7 inches wide, and 81.1 inches tall. In comparison, the H1 stretched 185 inches long, 87 inches wide, and about 78 inches tall. The electric powertrain also played a major role in slinging the Hummer's weight into dually pickup territory. Batteries are heavy, and the Hummer EV's Ultium pack reportedly has a capacity of over 200 kilowatt hours. It has three electric motors, too. Note the 9,046-pound figure applies only to the sold-out Launch Edition model, which will offer 1,000 horsepower, the aforementioned 200-kilowatt battery, and the supercar-like ability to hit 60 mph from a stop in three seconds. GMC will launch cheaper, slower, and presumably considerably lighter variants of the truck in the early 2020s. Although SUVs are often heavier than comparable trucks due to the additional sheet metal, the people-hauling Hummer should weigh less than the cargo-carrying variant. As we reported in April 2021, its output will be limited to 830 horsepower because it's 20 inches shorter than the truck, and the bigger battery pack doesn't fit in this footprint.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck