1999 Gmc Yukon Slt Sport Utility 4-door 5.7l (denali) on 2040-cars

Auto blog

2013 GMC Acadia priced from $34,875*

For those who are interested in the reworked 2013 GMC Acadia, we now know how much you can look forward to forking over. Base MSRP for the 2013 version of the full-size, three-row crossover has been set at $34,875 (*not including a $825 destination charge). If you are interested in the range-topping Denali trim, be prepared to pay $46,770.
The 2013 Acadia will come standard with a backup camera, leather-wrapped steering wheel, USB port and recycled visuals from the now-dead Saturn Outlook.
Upping to the Denali trim gets you a head-up display, blind spot monitoring system and GMC's new Rear Cross Traffic Alert system. According to GMC, most trims will also receive IntelliLink connectivity as standard equipment. The Acadia will also get the industry's first front-center airbag, an innovation it shares with other Lambda-based crossovers like the refreshed 2013 Buick Enclave. The idea behind the new tube-shaped airbag is that it can provide a buffer between driver and front seat passenger in the event of an impact, or better hold the driver in place if he or she is alone.

2014 GMC Sierra 4.3L V6 to offer segment-best 305 LB-FT

General Motors has released more information on the 4.3-liter V6 available in the 2014 GMC Sierra. The engine will serve up 285 horsepower and 305 pound-feet of torque, with a six-speed automatic transmission, and giving the V6 Sierra a maximum tow rating of 7,200 pounds in regular cab, short bed four-wheel drive configuration. GM claims that figure is 500 pounds more than the equivalent Ford F-150 equipped with a 3.7-liter V6, and 700 pounds more than the Ram 1500 with its 3.6-liter V6. Buyers can expect to see the 2014 GMC Sierra with the 4.3-liter engine start at $25,085 including destination.
While the engine does deliver more torque than either of its main competitors, it falls short on the horsepower front. The 3.7-liter V6 in the F-150 develops 302 hp while the 3.6-liter V6 in the Ram 1500 yields 305 hp. GM says fuel economy estimates for its newest entry will land later this year. Check out the full press release below for more information.

Chevy's 6.6-liter Duramax is pretty much all new

To say there's a heated battle in heavy-duty pickups is an understatement, with Chevrolet, Ford, and Ram constantly trading blows of increased torque, horsepower, and towing capacity. The latest salvo is the revised, more powerful turbo diesel 6.6-liter Duramax V8 in the 2017 Chevy Silverado. It has 910 pound-feet of torque, an increase of 145, putting it nearly level with the Ford Super Duty. Here's a closer look at where those gains come from. How exactly did Chevrolet add all that torque plus 48 horsepower? The automaker essentially took a fine-tooth comb to the entire engine. Chevy says it changed 90 percent of the V8, and the cumulative effect of those small changes adds up to big increases. As you might guess, the turbocharger is updated. The larger unit features electric actuation of the variable nozzle turbine (VNT), and what Chevy calls a double axle cartridge mechanism that separates the VNT moving parts from the housing. That helps with heat performance as well, with a claim that the exhaust side of the turbo can run continuously up to 1,436 degrees Fahrenheit. Helping that cause are six exhaust gaskets made of Inconel - an nickel alloy that contains chromium and iron – and upgraded stainless steel for the exhaust manifold. Despite having the same cast iron cylinder block, albeit with some minor enhancements, the engine has new cylinder heads, pistons, piston pins, connecting rods, and crankshaft, which have all been upgraded to handle 20 percent higher cylinder pressures. Alongside the increase in pressure, Chevrolet also increased the cylinder head's structure with a honeycomb design. The pattern features high-strength aluminum with dual layer water jackets that not only improve strength, but also optimize water flow for better cooling. For 2017, the cylinder head also benefits from integrated plenum that aids the engine in getting more air under heavy loads. The cylinder head isn't the only component to get a minor update, as the pistons have a larger diameter pin for improved oil flow. The same detailed improvements has been bestowed to the humble connecting rods (second in our hearts only to the inanimate carbon rod). The new design has the bolts oriented roughly 45-degrees to the rod instead of parallel. The angle split design, as it's called allows for easier passage through the cylinder.