2014 Gmc Terrain Sle on 2040-cars

Auto blog

2017 GMC Acadia loses 700 pounds, gains everywhere else

Ladies and gentlemen, welcome to Acadia. The 2017 version of the three-row GMC crossover has all kinds of newness. The 2017 Acadia has lost 700 pounds compared to its predecessor thanks to high-strength steels allowing redesigned parts, and the fact that it overall, the vehicle is actually smaller. Length is reduced by 7.2 inches on a wheelbase diminished by 6.4 inches, it is 3.5 inches narrower and sits 3.9 inches lower. The 2016 Acadia was 4,656 pounds, the 2017 is 3,956 pounds. GMC says it will still swallow people, but not as many: the eight-passenger option didn't make the transition, potential three-row trims permitting five-, six-, and seven-passenger configurations. While you lose space, you gain convenience with a split-folding second row featuring tilt-and-slide for both sections. The third-row seats fold flat into the cargo floor, and if the second row is folded as well, cargo capacity improves over the 2016 Acadia, 79 cubic feet compared to 70 cu-ft. A new 2.5-liter four-cylinder brings a second engine option to the spec sheet, returning an estimated 22 city miles per gallon and 28 highway mpg with the help of stop/start tech on front-wheel-drive trims. The new 3.6-liter V6 gets around 310 horsepower, a power bump of about 19 hp, and an estimated 25 highway mpg in front-wheel-drive guise. Towing capacity for that V6 goes down, though, from 5,200 on the current Acadia to an estimated 4,000 pounds. The optional Tow Vision Trailering system will make that pulling easier. Both engines are hooked to a six-speed automatic. Now we can get to its looks. Trademarks like the square, flared wheel arches, dark D-pillars, and wraparound rear side windows made the transition, everything else is new. While weight has gone down, safety's gone way up with internal changes like the splayed chassis members to confront the small-offset test. New active safety upgrades run from from three kinds of automatic braking systems to surround vision cameras, automatic high beam control, a safety alert seat, and a following distance indicator. Buyers can choose from a front-wheel drive, all-wheel drive, or All Terrain model, each with its own electronic drive selector modes. The Normal, Sport, and Trailer/Tow modes are common to the trio. The FWD gets a Snow mode, the AWD adds adaptive 4x4 and Off Road modes; on the AWD, the 2x4 mode disconnects the rear axle from the drivetrain.

2019 GMC Sierra carbon fiber bed: How it's made

FORT WAYNE, Ind. — The redesigned 2019 GMC Sierra has some pretty nifty features, and the one that has had the most attention is the MultiPro flipping and folding tailgate. But the Sierra also features the first-of-its-kind carbon fiber truck bed. It's interesting, of course, for its capabilities, such as being 62 pounds lighter than the all-steel box. It even adds more cargo volume since the material can be assembled and shaped differently from steel. As it turns out, the assembly process is cool, too, which we learned when GMC invited us to see the beds being made. Every GMC carbon fiber bed starts out as perfectly flat sheets of thermoplastic carbon fiber. The sheets consist of a mix of fibers and resins, a bit like the molded carbon fiber parts Lamborghini uses. The sheets are manufactured by Japanese company Teijin, which collaborated with GMC to develop the bed. They're all delivered to Continental Structural Plastics (CSP) in Fort Wayne, Ind., for construction into the actual bed. The company, a subsidiary of Teijin, makes a wide variety of composite and plastic parts for the car industry, including body panels for the C7 Chevy Corvette. The rectangular sheets are cut to shape and stacked up at a giant stamping press. Robots pick up sheets and slide them onto a conveyor that goes into a large oven. The heat softens the parts so they can be stamped. The large primary bed parts such as the base are stamped by CSP's enormous 3,600-ton press, and the smaller ones go through a 1,000-ton press. Each press can do different parts using different stamping dies, and CSP switches between dies to produce different batches of parts. After stamping, the parts roll out mostly ready for assembly, but there are rough edges that are trimmed off by water-jet cutters. These cutting machines also create holes for fasteners and for parts such as tie-down hooks and lights. The stamping process also provides the carbon fiber bed with a unique Easter egg. On the bottom of the base of the bed, there are two words: "Connors Way." This is a tribute to Tim Connors, who was the chief engineer of manufacturing at GM and a strong proponent of the carbon fiber bed. He was tragically killed in a motorcycle crash a few years ago. The words were added to honor him, and they were fortunately approved for production. There are some components to the bed that aren't stamped from the flat sheets of material.

GMC boss wants a Jeep Wrangler rival

Challengers come and challengers go, but the Jeep Wrangler continues to push forward even after vehicles like the Toyota FJ Cruiser and the entire Hummer brand have been shut down. Now GMC reportedly wants to take a stab at the quintessential Jeep, as well.
The news comes directly from Buick-GMC vice president Duncan Aldred, speaking with our compatriots over at Edmunds. Although Aldred said there are no plans currently on the table to expand GMC's lineup beyond the current range, "there is plenty of room everywhere in the hierarchy."
That could include a rival to the Wrangler, as well as a flagship luxury SUV positioned above the current Yukon Denali (pictured above). Just when (or for that matter, if) such models might come into fruition remains a big question mark, but it's certainly interesting to see what GM's dedicated truck brand has on the drawing board.