Gmc Chevy 3500 Hd Diesel Mechanics Utility Service Crane Truck 6k Lb. Auto Crane on 2040-cars

Auto blog

2019 GMC Sierra 1500 prototype shows off differences from Silverado

Now that the new Silverado has made its debut, we're awaiting the reveal of its mildly restyled twin, the GMC Sierra 1500. While it likely won't be that different as far as capability and major equipment are concerned, we are looking forward to seeing what design changes it will have. Based on these recent spy shots, the changes will be mild, but still enough to make it visually distinctive. One of the more obvious differences will be in the front fascia treatment. Unlike the Silverado's grille that's level with the top of the headlights, the GMC's will rise above the lights, which will also yield a slight drop on each side of the hood to meet the lights. The grille is quite tall, extending far below the headlights, too. We can make out, behind some mesh, two dips on the outer edges of the grille that give the Sierra a more menacing frown. Large foglights are also found right near where the scoops for the wheel air curtains, and the headlights are unified on the edges, rather than split on the Silverado. Along the sides, the sheet metal looks relatively unchanged. At some angles, we can make out the distinctive shoulder line from the Silverado that runs up to about the rear mirrors where it stops to make room for another crease that rises up from somewhere in the middle of the front doors to lead to the front. The wheel arches are decidedly different from the Silverado's though. While the Silverado has fairly rounded arches, the Sierra's have a rear-slanted bevel to the fronts of the arches and a rounded 90-degree corner at the rears. There isn't much we can tell about the rear except for the taillights. They're quite large, and unlike the Silverado's, there aren't any areas where the sheet metal intrudes. It also appears that the tops of the taillights extend farther forward into the bed sides than the Chevy's. Because the Sierra has almost always been a mechanical twin of the Silverado, we expect it to offer the same 5.3-liter and 6.2-liter V8s, as well as the new 3.0-liter diesel inline-6. Also, being a GMC, it will likely have a flashy, chrome-laden Denali trim level. We also will see the fully revealed model soon, as Automotive News reports the debut will be on March 1. Related Video: Featured Gallery 2019 GMC Sierra 1500 spy shots View 39 Photos News Source: Automotive News Spy Photos GMC Truck chevrolet silverado

GMC Syclone spools up a storm on Jay Leno's Garage

A storm was brewing on American roads in the early 1990s. That's when Detroit's automakers were producing some of the hottest performance trucks ever devised – models like the Ford Lightning, GMC Typhoon, and its flyweight pickup sibling, the GMC Syclone. Jay Leno just happens to have one of the latter in his garage, and took it out to showcase in this latest video segment. The Syclone was an exercise in absurdity, and could not only trounce any other pickup on the road, it could outrun anything else GM made and just about anything else on the road – beating Ferraris and Porsches off the line. In a pickup, for crying out loud. The kicker is that its engine wasn't such a monster, either: under the hood sat a 4.3-liter turbocharged V6 pumping out what would seem by today's standards to be an adequate 280 horsepower and 350 pound-feet of torque. Even the smaller of the EcoBoost V6s available in today's Ford F-150 produces more than that. But in a lightweight, compact pickup, those figures were enough to propel the Syclone to 60 in 4.3 seconds and run the quarter-mile in 13.6 seconds. Long before the dune-jumping Ford F-150 SVT Raptor or even the Viper-powered Dodge Ram SRT-10, GM made fewer than 3,000 Syclones based on the compact Sonoma (sister to the Chevy S-10) and another 4,700 of the Typhoon, which was mechanically similar but more practical (albeit heavier) wagon bodywork from the Jimmy. But as Jay aptly points out, the Syclone was the one you wanted. Scope it out in the ten-minute video clip above.

GMC Hummer EV could have had the Chevrolet Avalanche's Midgate

One of the many rumors swirling around the GMC Hummer EV claimed the truck would resurrect the Midgate inaugurated by the original Chevrolet Avalanche. Although we now know there's no way to fully knock down the partition between the cab and the cargo box, the firm revealed the rumor wasn't entirely false. "There was [a Midgate] early on. We opted for the functionality of the drop glass in the back. With the package layout and things like that, it was not advantageous to pursue that one. And, the five-foot bed was kind of the industry standard in regards to price of entry in that segment," explained John Mack, the Hummer's exterior design management, during an interview with Muscle Car & Trucks. The Hummer will go on sale with a five-foot box, and it doesn't sound like a longer bed will be available, so a modern version of the Midgate would have made the model more versatile by giving users the ability to fold down the partition behind the rear seats to carry bulky items, like plywood and ATVs. It's a feature that would have inevitably made the truck more complicated to build, however, because it adds moving parts that need to be sealed. Hinges, seals, and latches in turn add weight, and complexity almost always invites high manufacturing costs. As an electric pickup built with newly-developed components, the Hummer already has enough of each. Motorists who need to carry something that's significantly longer than the cargo box aren't entirely out of luck. As Mack pointed out, the rear window drops into the partition, so owners will have the ability to haul surfboards, lumber, or anything else that's relatively long and reasonably thin by simply pushing a switch. Alternatively, the only thing limiting cargo space when the roof comes off is the sky — or, depending on where you live, bridges. Mack didn't reveal when the Midgate was dropped. GMC launched the Hummer project in April 2019, and it previously released early design sketches that show how the truck transitioned from a sketch to a prototype. As of writing, nothing suggests the Midgate will make a comeback in the near future on any member of the General Motors portfolio. It was introduced in 2001 on the first-generation Chevrolet Avalanche, which went on sale in the United States for the 2002 model year. It later spread to Cadillac's luxed-up variant of the truck, the Escalade EXT, and to the short-lived GMC Envoy XUV.