2021 Gmc Sierra 3500 Denali on 2040-cars

Auto blog

2020 GMC Acadia AT4 priced just a little more than the SLT trim

Cars Direct has seen the order guide pricing the 2020 Acadia AT4 at $42,495 after destination; that means a $41,300 MSRP plus $1,195 for shipping and handling. GMC has left a lot of pricing room between the rugged, all-wheel drive AT4 and the dressed-up, top-shelf Acadia Denali with AWD, the latter costing $49,495, a $7,000 difference. The spread's blown out some by what appears to be an $800 increase for the 2020 Acadia Denali with all-wheel drive. The 2019 model costs $48,695. On the other hand, it looks like the 200 Acadia SLT trim has gone down in price. Cars Direct says that model will run $41,995, which is $300 less than the 2019 version that goes for $42,295 after destination. The new price leaves a $500 gap between the SLT-1 model with all-wheel drive and the AT4 trim, a figure that's a no-brainer to justify for any buyers trying to get a more butch curb appeal.     The Acadia AT4 package comes standard with all-wheel drive and the 3.6-liter V6 with 310 horsepower and 271 pound-feet of torque, puts black chrome on the grille, and nabs a set of exclusive 17-inch wheels on all-terrain tires. The other two engines in the lineup are a new turbocharged 2.0-liter four-cylinder with 230 horsepower and 258 pound-feet of torque, and cylinder deactivation. That motor will be the standard kit on the SLT and Denali trim levels, supplanting the 3.6-liter that's standard on the 2019 models. The entry-level engine carries over, a naturally aspirated 2.5-liter four-cylinder making 193 horsepower and 188 pound-feet of torque.

IIHS: High numbers of drivers treat partially automated cars as fully self-driving

WASHINGTON — Drivers using advanced driver assistance systems like Tesla Autopilot or General Motors Super Cruise often treat their vehicles as fully self-driving despite warnings, a new study has found. The Insurance Institute for Highway Safety (IIHS), an industry funded group that prods automakers to make safer vehicles, said on Tuesday a survey found regular users of Super Cruise, Nissan/Infiniti ProPILOT Assist and Tesla Autopilot "said they were more likely to perform non-driving-related activities like eating or texting while using their partial automation systems than while driving unassisted." The IIHS study of 600 active users found 53% of Super Cruise, 42% of Autopilot and 12% of ProPILOT Assist owners "said that they were comfortable treating their vehicles as fully self-driving." About 40% of users of Autopilot and Super Cruise — two systems with lockout features for failing to pay attention — reported systems had at some point switched off while they were driving and would not reactivate. "The big-picture message here is that the early adopters of these systems still have a poor understanding of the technologyÂ’s limits," said IIHS President David Harkey. The study comes as the National Highway Traffic Safety Administration (NHTSA) is scrutinizing Autopilot crashes. Since 2016, the NHTSA has opened 37 special investigations involving 18 deaths in crashes involving Tesla vehicles and where systems like Autopilot were suspected of use. Tesla did not respond to requests for comment. Tesla says Autopilot does not make vehicles autonomous and is intended for use with a fully attentive driver who is prepared to take over. GM, which in August said owners could use Super Cruise on 400,000 miles (643,740 km) of North American roads and plans to offer Super Cruise on 22 models by the end of 2023, did not immediately comment. IIHS said advertisements for Super Cruise focus on hands-free capabilities while Autopilot evokes the name used in passenger airplanes and "implies TeslaÂ’s system is more capable than it really is." IIHS in contrast noted ProPILOT Assist "suggests that itÂ’s an assistance feature, rather than a replacement for the driver." NHTSA and automakers say none of the systems make vehicles autonomous. Nissan said its name "is clearly communicating ProPILOT Assist as a system to aid the driver, and it requires hands-on operation.

GM dealers have ordered 30k Colorado and Canyon pickups, 3rd shift added

General Motors has an early success on its hands in the form of the initial rollout of the Chevy Colorado and GMC Canyon midsize pickup trucks. According to the automaker, dealers have ordered nearly 30,000 of the trucks thus far, a number that far exceeded GM's early expectations.
This high demand for the Colorado and Canyon twins has prompted GM to add a third shift to its Wentzville Assembly plant where the trucks are built, starting early next year. An extra shift will add an additional 750 jobs at the location to the 1,315 that were already employed there, according to the press release that you're welcome to read down below.
Such positive sales projections for the Canyon and Colorado may portend good things for the midsize pickup segment, which was once hugely popular but has more recently contracted, with the Nissan Frontier and Toyota Tacoma standing firm as the market leaders. Now that GM's entries are the most up-to-date, and with the segment's first diesel engine on the way, it will be interesting to see how the trucks continue to sell and if their hopeful success leads more automakers back onto the playing field.