2014 Gmc Sierra 2500 Sle on 2040-cars

Auto blog

GMC Sierra Denali CarbonPro bed is finally, almost here

GMC revealed the Sierra 1500 with the optional CarbonPro bed on March 1, 2018. The bed wasn't available at launch, though. You can't buy it now, either, but it will hit dealerships with limited availability after production starts in early June, exclusively for the Denali 1500 and AT4 1500 trims. The carbon floor and sides replace the steel panels in a normal bed, providing "strength, durability, and scratch resistance" and a potential 59-pound weight saving, depending on the truck's configuration. To make sure the bed had a chance, development engineers replicated "extreme use scenarios" like dropping 1,800-pound gravel loads, 450-pound steel drums, and cinder blocks from various heights. They put a 250-pound man on a snowmobile with studded tracks, had him drive into the bed and then go wide-open throttle. We're told the result was "minimal scratching." On top of the extreme weather testing any vehicle goes through, the team also put a generator in the bed and aim the exhaust into a corner to ensure vibration and direct heat wouldn't deform the carbon fiber. Because of the finer shaping area-specific strength possible with carbon fiber, the bed provides one cubic foot of additional payload space by having its sidewalls pushed further out. The CarbonPro bed doesn't need a bedliner, and is grained at the top for better traction but smooth on the bottom for easier hosing down and dirt removal. Tie-downs at the front of the bed work with molded indentations to hold motorcycle tires, and slots in the sidewalls hold two-by-sixes. The truck maker says the carbon-lined payload area confers "best-in-class dent, scratch and corrosion resistance," but we suppose the nation's pickup truck army will prove that or not. The trucks likely won't have the hardest life at the start, since the Sierra Denali costs $56,790 before even a basic option like four-wheel drive. The real test probably won't come until around 2029, when third owners begin treating their aerospace-inspired thoroughbreds like dray horses.

GMC Syclone spools up a storm on Jay Leno's Garage

A storm was brewing on American roads in the early 1990s. That's when Detroit's automakers were producing some of the hottest performance trucks ever devised – models like the Ford Lightning, GMC Typhoon, and its flyweight pickup sibling, the GMC Syclone. Jay Leno just happens to have one of the latter in his garage, and took it out to showcase in this latest video segment. The Syclone was an exercise in absurdity, and could not only trounce any other pickup on the road, it could outrun anything else GM made and just about anything else on the road – beating Ferraris and Porsches off the line. In a pickup, for crying out loud. The kicker is that its engine wasn't such a monster, either: under the hood sat a 4.3-liter turbocharged V6 pumping out what would seem by today's standards to be an adequate 280 horsepower and 350 pound-feet of torque. Even the smaller of the EcoBoost V6s available in today's Ford F-150 produces more than that. But in a lightweight, compact pickup, those figures were enough to propel the Syclone to 60 in 4.3 seconds and run the quarter-mile in 13.6 seconds. Long before the dune-jumping Ford F-150 SVT Raptor or even the Viper-powered Dodge Ram SRT-10, GM made fewer than 3,000 Syclones based on the compact Sonoma (sister to the Chevy S-10) and another 4,700 of the Typhoon, which was mechanically similar but more practical (albeit heavier) wagon bodywork from the Jimmy. But as Jay aptly points out, the Syclone was the one you wanted. Scope it out in the ten-minute video clip above.

GM thinks Colorado and Canyon midsize trucks will lure crossover buyers

The invitation to come out and sample product at the General Motors Proving Grounds in Milford, MI is rarely dull, and after spending this morning driving preproduction versions of the Chevrolet Colorado and GMC Canyon all we can say is... under strict embargo. Sorry, America, we were as excited as many of you are to learn more about GM's new midsize truck range and take note of how they go down the road, but it's going to be September before we're allowed to share that with all of you. Here's to sweet suspense.
While we might not be able to talk about refinement or handling yet, we did find some of the product positioning and marketing statements from GMC and Chevy officials on hand at the program to be pretty interesting.
Of course, we all know that the literal competitive set for Canyon and Colorado is comprised of two comparatively ancient Japanese midsize trucks: the Toyota Tacoma (which currently owns this segment) and the Nissan Frontier. The Frontier's bones are as old as the 2005 model year, with 2009 marking the last time the truck was updated. The Taco was also launched in 2005, though it did see a freshening for 2012. The point remains that, in every facet from powertrain to dash plastics, the GM midsize truck twins are going to look positively space age by comparison when they hit the market for MY 2015.