Gmc Sierra 1500 With Crew Cab And Work Camper Shell on 2040-cars

Auto blog

GMC to get own model not shared with Chevy?

For years, GMC has existed as a brand without a single unique product, reconstituting Chevrolet trucks, SUVs and crossovers with more frosting in exchange for a few extra dollars. The Sierra is a Silverado, the Acadia a Traverse, and the Terrain an Equinox, although admittedly the latter pair are visually differentiated to a significant degree.
GMC could be set to expand beyond its Chevy-based roots, though. During last week's Detroit Auto Show press days, GM's product boss Mark Reuss was asked whether there'd ever be a GMC that wasn't taken from Chevy. "Oh, yes, you will," Reuss told the media. "The health of GMC is astonishingly good from a consideration standpoint." Reuss wouldn't elaborate on what the model could be, although we're quite happy to make some guesses. GMC has its bases fairly well covered, with a mid-size and full-size crossover, as well as a mid-size, full-size and HD pickup. We doubt GMC will be building a family sedan, sports car, or hatchback, so really, the only place we can see the brand going is into a smaller crossover.
Automotive News points out that the most recent small GMC showcar, the 2010 Granite concept (shown above), won't see production according to General Motors. That vehicle likely would have rode on GM's compact vehicle architecture, known internally as Gamma II, which underpins the Chevy Spark and Sonic, as well as the Buick Encore (and its overseas Opel/Vauxhall/Chevy counterparts).

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

GMC Sierra Denali CarbonPro bed is finally, almost here

GMC revealed the Sierra 1500 with the optional CarbonPro bed on March 1, 2018. The bed wasn't available at launch, though. You can't buy it now, either, but it will hit dealerships with limited availability after production starts in early June, exclusively for the Denali 1500 and AT4 1500 trims. The carbon floor and sides replace the steel panels in a normal bed, providing "strength, durability, and scratch resistance" and a potential 59-pound weight saving, depending on the truck's configuration. To make sure the bed had a chance, development engineers replicated "extreme use scenarios" like dropping 1,800-pound gravel loads, 450-pound steel drums, and cinder blocks from various heights. They put a 250-pound man on a snowmobile with studded tracks, had him drive into the bed and then go wide-open throttle. We're told the result was "minimal scratching." On top of the extreme weather testing any vehicle goes through, the team also put a generator in the bed and aim the exhaust into a corner to ensure vibration and direct heat wouldn't deform the carbon fiber. Because of the finer shaping area-specific strength possible with carbon fiber, the bed provides one cubic foot of additional payload space by having its sidewalls pushed further out. The CarbonPro bed doesn't need a bedliner, and is grained at the top for better traction but smooth on the bottom for easier hosing down and dirt removal. Tie-downs at the front of the bed work with molded indentations to hold motorcycle tires, and slots in the sidewalls hold two-by-sixes. The truck maker says the carbon-lined payload area confers "best-in-class dent, scratch and corrosion resistance," but we suppose the nation's pickup truck army will prove that or not. The trucks likely won't have the hardest life at the start, since the Sierra Denali costs $56,790 before even a basic option like four-wheel drive. The real test probably won't come until around 2029, when third owners begin treating their aerospace-inspired thoroughbreds like dray horses.