2002 Gmc Sierra 1500 Sle on 2040-cars

Auto blog

2019 GMC Sierra 1500 prototype shows off differences from Silverado

Now that the new Silverado has made its debut, we're awaiting the reveal of its mildly restyled twin, the GMC Sierra 1500. While it likely won't be that different as far as capability and major equipment are concerned, we are looking forward to seeing what design changes it will have. Based on these recent spy shots, the changes will be mild, but still enough to make it visually distinctive. One of the more obvious differences will be in the front fascia treatment. Unlike the Silverado's grille that's level with the top of the headlights, the GMC's will rise above the lights, which will also yield a slight drop on each side of the hood to meet the lights. The grille is quite tall, extending far below the headlights, too. We can make out, behind some mesh, two dips on the outer edges of the grille that give the Sierra a more menacing frown. Large foglights are also found right near where the scoops for the wheel air curtains, and the headlights are unified on the edges, rather than split on the Silverado. Along the sides, the sheet metal looks relatively unchanged. At some angles, we can make out the distinctive shoulder line from the Silverado that runs up to about the rear mirrors where it stops to make room for another crease that rises up from somewhere in the middle of the front doors to lead to the front. The wheel arches are decidedly different from the Silverado's though. While the Silverado has fairly rounded arches, the Sierra's have a rear-slanted bevel to the fronts of the arches and a rounded 90-degree corner at the rears. There isn't much we can tell about the rear except for the taillights. They're quite large, and unlike the Silverado's, there aren't any areas where the sheet metal intrudes. It also appears that the tops of the taillights extend farther forward into the bed sides than the Chevy's. Because the Sierra has almost always been a mechanical twin of the Silverado, we expect it to offer the same 5.3-liter and 6.2-liter V8s, as well as the new 3.0-liter diesel inline-6. Also, being a GMC, it will likely have a flashy, chrome-laden Denali trim level. We also will see the fully revealed model soon, as Automotive News reports the debut will be on March 1. Related Video: Featured Gallery 2019 GMC Sierra 1500 spy shots View 39 Photos News Source: Automotive News Spy Photos GMC Truck chevrolet silverado

2022 Hummer EV Edition 1 pickups ready to go to customers

It's official: Two years after GM announced the electric GMC Hummer pickup, the first couple dozen units have left the line at the GM Factory Zero Detroit-Hamtramck Assembly Center, according to GM president Mark Reuss. In an interview with CNBC to celebrate the milestone, Reuss said 17 Hummer EVs are ready for delivery to customers. This makes the Hummer the first of GM's new Ultium-based EVs to leave the factory, and the second electric pickup on the market after the Rivian R1T. The first 1,200 Hummer EVs made will be Edition 1 models, all of which are Interstellar White outside with Lunar Horizon interiors and bronze badging. Each of the $112,595 pickups is powered by three Ultium motors producing a GM-estimated 1,000 horsepower and 11,500 pound-feet of torque, loaded with features like height-adjusting adaptive suspension, skid rails and rock sliders, 35-inch tires, the diagonal-driving CrabWalk, the launch control system Watts to Freedom that unlocks a three-second sprint to 60 miles per hour, and Super Cruise. Range is a GM-estimated 329 miles when the 200-kWh battery is fully charged. As these filter out to eager owners, GM is prepping the next four phases of the Hummer rollout. About a year from now, in autumn of 2022, Factory Zero will begin production of the first widely available Hummer, the EV3X pickup that starts at $99,995 before destination. Three Ultium motors will provide an estimated 800 horsepower and 9,500 pound-feet of torque to a range estimated beyond 300 miles. Spring of 2023 is expected to deliver the Hummer EV2X pickup at an MSRP of $89,995, utilizing two motors producing a total 625 hp and 7,400 lb-ft over a range also estimated to go beyond 300 miles. Around the same time, the first units of the $105,595 Hummer SUV Edition 1 are planned to head down lines at Factory Zero. Finally, in the spring of 2024, the entry-level $79,995 Hummer EV2 pickup and its two-motor powertrain should arrive, making the same output as the EV2X, but only good for a range of around 250 miles. That won't be all we see from Factory Zero, either. GM invested $2.2 billion in the Detroit-Hamtramck plant that once built bread-and-butter GM fare like the Chevrolet Impala, Buick LaCrosse, and Oldsmobile Toronado in order to turn the facility into its first EV base of manufacturing operations for Ultium products. The battery-electric Chevrolet Silverado and GMC Sierra pickups will be built there, as will the Cruise Origin robotaxi.

GM readying aluminum-body fullsize pickups

Ford's extensive use of aluminum in its 2015 F-150 is a big deal. A really big deal. Big enough, in fact, that General Motors is reportedly changing its fullsize pickup strategy. According to The Wall Street Journal, The General has locked in partnerships with Alcoa Inc. and Novelis Inc. - companies that will supply aluminum for the next-generation Chevrolet Silverado and GMC Sierra trucks.
"Ford's introduction of the 2015 F-150 pickup truck was a game changer, and it's the first, not the last, conversion of this type," Novelis spokesperson Charles Belbin told the Journal. The switch to aluminum has allowed Ford to shave roughly 700 pounds off its fullsize truck's curb weight. And while official mileage ratings have not been announced, the weight loss should go a long way for improving efficiency, especially when combined other efficiency-minded improvements including better aerodynamics and new, turbocharged V6 engines.
Of course, aluminum-bodied cars are nothing new. But extensive use of aluminum in a major, best-selling product like the Ford F-150 is expected to kick off widespread use of this weight-saving material as availability rises and cost decreases. The WSJ reports that GM had originally explored the idea of moving to aluminum pickups back in 2008, but abandoned the idea due to cost concerns amid economic woes.