12 4wd New 7" Lift Fuel 20's 35" Tires Like New V8 Auto Net Direct Auto Texas on 2040-cars

Auto blog

2013 GMC Acadia priced from $34,875*

For those who are interested in the reworked 2013 GMC Acadia, we now know how much you can look forward to forking over. Base MSRP for the 2013 version of the full-size, three-row crossover has been set at $34,875 (*not including a $825 destination charge). If you are interested in the range-topping Denali trim, be prepared to pay $46,770.
The 2013 Acadia will come standard with a backup camera, leather-wrapped steering wheel, USB port and recycled visuals from the now-dead Saturn Outlook.
Upping to the Denali trim gets you a head-up display, blind spot monitoring system and GMC's new Rear Cross Traffic Alert system. According to GMC, most trims will also receive IntelliLink connectivity as standard equipment. The Acadia will also get the industry's first front-center airbag, an innovation it shares with other Lambda-based crossovers like the refreshed 2013 Buick Enclave. The idea behind the new tube-shaped airbag is that it can provide a buffer between driver and front seat passenger in the event of an impact, or better hold the driver in place if he or she is alone.

2015 GMC Yukon erupts into flames during Anaheim test drive [w/video]

A 2015 GMC Yukon burst into flames while on a test drive in Anaheim, CA on Sunday after smoke filled the cabin. Residents of the neighborhood where the driver abandoned the redesigned Yukon reported hearing a series of small explosions (likely the tires, based on the video), according to a report from KTLA and The Los Angeles Times.
No one was injured in the incident, which The Times reports occurred after a possible oil or fluid leak. As you can see in the image above, the Yukon was engulfed in flames, although the Anaheim Fire Department was able to put out the blaze in about 15 minutes.
"We're very lucky that no one got hurt, and it was in an area that... was safe," Lt. Tim Schmidt of the Anaheim Police Department told KTLA reporters. "If there was any place that was going to be safe, it would be this area. It's very open. It worked out for us."

2019 GMC Sierra carbon fiber bed: How it's made

FORT WAYNE, Ind. — The redesigned 2019 GMC Sierra has some pretty nifty features, and the one that has had the most attention is the MultiPro flipping and folding tailgate. But the Sierra also features the first-of-its-kind carbon fiber truck bed. It's interesting, of course, for its capabilities, such as being 62 pounds lighter than the all-steel box. It even adds more cargo volume since the material can be assembled and shaped differently from steel. As it turns out, the assembly process is cool, too, which we learned when GMC invited us to see the beds being made. Every GMC carbon fiber bed starts out as perfectly flat sheets of thermoplastic carbon fiber. The sheets consist of a mix of fibers and resins, a bit like the molded carbon fiber parts Lamborghini uses. The sheets are manufactured by Japanese company Teijin, which collaborated with GMC to develop the bed. They're all delivered to Continental Structural Plastics (CSP) in Fort Wayne, Ind., for construction into the actual bed. The company, a subsidiary of Teijin, makes a wide variety of composite and plastic parts for the car industry, including body panels for the C7 Chevy Corvette. The rectangular sheets are cut to shape and stacked up at a giant stamping press. Robots pick up sheets and slide them onto a conveyor that goes into a large oven. The heat softens the parts so they can be stamped. The large primary bed parts such as the base are stamped by CSP's enormous 3,600-ton press, and the smaller ones go through a 1,000-ton press. Each press can do different parts using different stamping dies, and CSP switches between dies to produce different batches of parts. After stamping, the parts roll out mostly ready for assembly, but there are rough edges that are trimmed off by water-jet cutters. These cutting machines also create holes for fasteners and for parts such as tie-down hooks and lights. The stamping process also provides the carbon fiber bed with a unique Easter egg. On the bottom of the base of the bed, there are two words: "Connors Way." This is a tribute to Tim Connors, who was the chief engineer of manufacturing at GM and a strong proponent of the carbon fiber bed. He was tragically killed in a motorcycle crash a few years ago. The words were added to honor him, and they were fortunately approved for production. There are some components to the bed that aren't stamped from the flat sheets of material.