08 Gmc Sierra 1500 Vmax Lifted on 2040-cars

Auto blog

2019 GMC Sierra 1500 prototype shows off differences from Silverado

Now that the new Silverado has made its debut, we're awaiting the reveal of its mildly restyled twin, the GMC Sierra 1500. While it likely won't be that different as far as capability and major equipment are concerned, we are looking forward to seeing what design changes it will have. Based on these recent spy shots, the changes will be mild, but still enough to make it visually distinctive. One of the more obvious differences will be in the front fascia treatment. Unlike the Silverado's grille that's level with the top of the headlights, the GMC's will rise above the lights, which will also yield a slight drop on each side of the hood to meet the lights. The grille is quite tall, extending far below the headlights, too. We can make out, behind some mesh, two dips on the outer edges of the grille that give the Sierra a more menacing frown. Large foglights are also found right near where the scoops for the wheel air curtains, and the headlights are unified on the edges, rather than split on the Silverado. Along the sides, the sheet metal looks relatively unchanged. At some angles, we can make out the distinctive shoulder line from the Silverado that runs up to about the rear mirrors where it stops to make room for another crease that rises up from somewhere in the middle of the front doors to lead to the front. The wheel arches are decidedly different from the Silverado's though. While the Silverado has fairly rounded arches, the Sierra's have a rear-slanted bevel to the fronts of the arches and a rounded 90-degree corner at the rears. There isn't much we can tell about the rear except for the taillights. They're quite large, and unlike the Silverado's, there aren't any areas where the sheet metal intrudes. It also appears that the tops of the taillights extend farther forward into the bed sides than the Chevy's. Because the Sierra has almost always been a mechanical twin of the Silverado, we expect it to offer the same 5.3-liter and 6.2-liter V8s, as well as the new 3.0-liter diesel inline-6. Also, being a GMC, it will likely have a flashy, chrome-laden Denali trim level. We also will see the fully revealed model soon, as Automotive News reports the debut will be on March 1. Related Video: Featured Gallery 2019 GMC Sierra 1500 spy shots View 39 Photos News Source: Automotive News Spy Photos GMC Truck chevrolet silverado

Car theft skyrockets thanks to rising parts prices

Cars and trucks today have achieved a high level of average quality, with safety and technology features that keep occupants safer than ever and meet consumers' high expectations. But the National Insurance Crime Bureau finds that those components come with a rising price tag, leading to expensive repair bills — and rising vehicle thefts to support a thriving black market for parts. The nonprofit NICB said it looked at the cost of replacement parts for the top 10 stolen 2016 models, with average OEM part prices pulled from a database of more than 24 million vehicle damage appraisals generated for 2016 and 2017 insurance claims. The list did not include major components like engines or transmissions, only easily-stripped components like bumpers, doors, hoods and headlights. It found that: The 2016 Toyota Camry, which had a used market value of around $15,000, had 15 commonly replaced parts that added up to almost $11,000, not including labor, with quarter panels alone costing almost $1,600 a pair and a set of alloy wheels tallying more than $1,600. The Camry was also the top stolen vehicle in 2016 at 1,113 thefts. A 2016 Nissan Altima had 14 standard parts worth more than $14,000, including a single headlamp assembly that costs just over $1,000. The Altima was the second-top stolen vehicle in 2016 at 1,063 vehicles stolen. And the 2016 GMC Sierra pickup, which was No. 7 on the 2016 top-stolen list, rang up $21,000 from 20 standard components, including an $1,100 headlamp assembly and an $1,100 rear bumper. "For the professional theft ring, stealing and stripping vehicles for parts has always been a lucrative business," Jim Schweitzer, NICB's senior vice president and chief operating officer, said in a statement. "On today's cars and trucks, the parts are often worth more than the intact vehicle and may be easier to move and sell. That's why we see so many thefts of key items like wheels and tires and tailgates ... there's always a market for them." Check out the NICB infographic below. Vehicle thefts in the U.S. rose by more than 4 percent in 2017, based on preliminary FBI data, after rising 7.6 percent in 2016, though the overall trend has been down since vehicle thefts peaked in 1991, according to the NICB. Related Video: Image Credit: National Insurance Crime Bureau Aftermarket GMC Nissan Toyota Auto Repair Insurance Ownership auto parts car values stolen car nicb national insurance crime bureau components

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck