on 2040-cars

Auto blog

GMC Sierra Denali CarbonPro bed is finally, almost here

GMC revealed the Sierra 1500 with the optional CarbonPro bed on March 1, 2018. The bed wasn't available at launch, though. You can't buy it now, either, but it will hit dealerships with limited availability after production starts in early June, exclusively for the Denali 1500 and AT4 1500 trims. The carbon floor and sides replace the steel panels in a normal bed, providing "strength, durability, and scratch resistance" and a potential 59-pound weight saving, depending on the truck's configuration. To make sure the bed had a chance, development engineers replicated "extreme use scenarios" like dropping 1,800-pound gravel loads, 450-pound steel drums, and cinder blocks from various heights. They put a 250-pound man on a snowmobile with studded tracks, had him drive into the bed and then go wide-open throttle. We're told the result was "minimal scratching." On top of the extreme weather testing any vehicle goes through, the team also put a generator in the bed and aim the exhaust into a corner to ensure vibration and direct heat wouldn't deform the carbon fiber. Because of the finer shaping area-specific strength possible with carbon fiber, the bed provides one cubic foot of additional payload space by having its sidewalls pushed further out. The CarbonPro bed doesn't need a bedliner, and is grained at the top for better traction but smooth on the bottom for easier hosing down and dirt removal. Tie-downs at the front of the bed work with molded indentations to hold motorcycle tires, and slots in the sidewalls hold two-by-sixes. The truck maker says the carbon-lined payload area confers "best-in-class dent, scratch and corrosion resistance," but we suppose the nation's pickup truck army will prove that or not. The trucks likely won't have the hardest life at the start, since the Sierra Denali costs $56,790 before even a basic option like four-wheel drive. The real test probably won't come until around 2029, when third owners begin treating their aerospace-inspired thoroughbreds like dray horses.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

GM recalls 3.6 million vehicles for airbag-software problems

The Basics: General Motors is recalling 3.64 million vehicles across its lineup for an airbag-related issue. The recall covers the 2014-2015 Buick LaCrosse, Chevrolet SS, and Spark EV; 2014-2017 Chevrolet Corvette, Trax, Caprice PPV, Silverado 1500, Buick Encore, and GMC Sierra 1500; and 2015-2017 Chevrolet Tahoe, Suburban, Silverado HD, GMC Yukon, Yukon XL, Sierra HD, Cadillac Escalade, and Escalade ESV. The Problem: Affected vehicles have a sensing and diagnostic module that controls the airbags and seat-belt pretensioners. The software it uses has a defect that can prompt the module to run a diagnostic test under specific driving conditions, which will also deactivate the front airbags and pretensioners. This means that it would be possible for those safety systems to not activate in a crash, potentially leading to injury or death. Injuries/Deaths: General Motors began an investigation that led to the recall after a 2014 Silverado was involved in a crash in which the airbags did not deploy. No information was given as to injuries or deaths. The Fix: Owners can bring their vehicles to a local General Motors dealer where a software update will be installed to fix the issue. The fix will be free of charge. If you own one: General Motors will contact owners of affected cars, and owners can check whether their vehicles are affected by visiting entering their vehicle identification numbers at either the GM Owner Center website or the NHTSA website. Owners can then schedule a time to have the update installed. Related Video: