92 Gmc Jimmy 4 Door V6 5spd Lowered 4 Inch Southern Truck on 2040-cars

Auto blog

GM SUV window switch recall urges owners to park vehicles outside

It's not unusual for there to be a lag between an automaker announcing a recall and the official documentation showing up on the National Highway Traffic Safety Administration website. So it's no surprise that a recent GM campaign took about a month to appear in its official capacity. However, there appears to be some big differences between the two reports with potential safety implications.
In late June, GM announced that it needed to recall 181,984 examples of the Chevrolet Trailblazer, Buick Rainier, GMC Envoy, Isuzu Ascender and Saab 9-7x from the 2005-2007 model years, plus the 2006 Chevy Trailblazer EXT and 2006 GMC Envoy XL. The new documents paint a slightly different picture with 184,611 needing repaired and different model years listed.
The reason for the fix is still the same, though. It's possible for fluid to contact the master power window switch module in the driver's door, which can corrode the part. Eventually this could cause a short circuit, leaving the buttons inoperable and potentially leading to a fire. But the new NHTSA documents add an important note: "A fire could occur even while the vehicle is not in use. As a precaution, owners are advised to park outside until the remedy has been made."

GM's fullsize SUVs boost highway mileage by nearly 10 percent

We met the redesigned 2015 versions of the Chevrolet Suburban and Tahoe, and the GMC Yukon and Yukon XL at the 2013 LA Auto Show. Improved gas mileage numbers have been announced to go along with the improved exteriors and interiors, with city mileage improving by seven percent and highway mileage going up by nearly ten percent; you'll now get 16 miles per gallon in the city and 23 on the highway.
The only applies to models with the 5.3-liter engine, though, not the premium Yukon Denali and Yukon XL Denali SUVs with the 6.2-liter motor. Still, the 5.3 gets you more power than previously, with 355 horsepower and 383 pound-feet of torque underfoot, on top of the improved fuel economy numbers. The 6.2-liter sticks with official mpg ratings of 15 highway, 21 city. There's a brief press release below with words straight from the horse's mouth.

2019 GMC Sierra carbon fiber bed: How it's made

FORT WAYNE, Ind. — The redesigned 2019 GMC Sierra has some pretty nifty features, and the one that has had the most attention is the MultiPro flipping and folding tailgate. But the Sierra also features the first-of-its-kind carbon fiber truck bed. It's interesting, of course, for its capabilities, such as being 62 pounds lighter than the all-steel box. It even adds more cargo volume since the material can be assembled and shaped differently from steel. As it turns out, the assembly process is cool, too, which we learned when GMC invited us to see the beds being made. Every GMC carbon fiber bed starts out as perfectly flat sheets of thermoplastic carbon fiber. The sheets consist of a mix of fibers and resins, a bit like the molded carbon fiber parts Lamborghini uses. The sheets are manufactured by Japanese company Teijin, which collaborated with GMC to develop the bed. They're all delivered to Continental Structural Plastics (CSP) in Fort Wayne, Ind., for construction into the actual bed. The company, a subsidiary of Teijin, makes a wide variety of composite and plastic parts for the car industry, including body panels for the C7 Chevy Corvette. The rectangular sheets are cut to shape and stacked up at a giant stamping press. Robots pick up sheets and slide them onto a conveyor that goes into a large oven. The heat softens the parts so they can be stamped. The large primary bed parts such as the base are stamped by CSP's enormous 3,600-ton press, and the smaller ones go through a 1,000-ton press. Each press can do different parts using different stamping dies, and CSP switches between dies to produce different batches of parts. After stamping, the parts roll out mostly ready for assembly, but there are rough edges that are trimmed off by water-jet cutters. These cutting machines also create holes for fasteners and for parts such as tie-down hooks and lights. The stamping process also provides the carbon fiber bed with a unique Easter egg. On the bottom of the base of the bed, there are two words: "Connors Way." This is a tribute to Tim Connors, who was the chief engineer of manufacturing at GM and a strong proponent of the carbon fiber bed. He was tragically killed in a motorcycle crash a few years ago. The words were added to honor him, and they were fortunately approved for production. There are some components to the bed that aren't stamped from the flat sheets of material.