Gmc Acadia Sle 2007. Red. Leather Seats. on 2040-cars

Auto blog

NHTSA opens safety investigations into Toyota, GM and Honda crossovers

The National Highway Traffic Safety Administration is evidently keeping itself very busy these days, as the federal agency has just announced it is launching or renewing investigations into Toyota, Honda and General Motors crossovers.
2006-2008 model year Toyota RAV4 crossovers are under review for allegations of rear tie-rod rust which can result in failure. NHTSA also said it is probing some 35 complaints about 2005 Honda Pilot models with inappropriate activation of the vehicles' stability control system. The alleged malfunction can cause the vehicles to slow down or stop in bad unsafe situations. At the moment, NHTSA is reviewing a petition regarding the Pilot issue, a move that will determine whether it needs to open a full-blown investigation.
In addition, Saturn Outlook and GMC Acadia three-row crossovers built in 2007-2009 are getting looked at for "loss of low beam headlamp" function. One complainant said the wiring in his Outlook overheated and melted. NHTSA says it has received 415 complaints about the problem and a GM spokesman confirmed that the automaker already started a "Customer Satisfaction Program" in December to address the issue.

2019 GMC Sierra carbon fiber bed: How it's made

FORT WAYNE, Ind. — The redesigned 2019 GMC Sierra has some pretty nifty features, and the one that has had the most attention is the MultiPro flipping and folding tailgate. But the Sierra also features the first-of-its-kind carbon fiber truck bed. It's interesting, of course, for its capabilities, such as being 62 pounds lighter than the all-steel box. It even adds more cargo volume since the material can be assembled and shaped differently from steel. As it turns out, the assembly process is cool, too, which we learned when GMC invited us to see the beds being made. Every GMC carbon fiber bed starts out as perfectly flat sheets of thermoplastic carbon fiber. The sheets consist of a mix of fibers and resins, a bit like the molded carbon fiber parts Lamborghini uses. The sheets are manufactured by Japanese company Teijin, which collaborated with GMC to develop the bed. They're all delivered to Continental Structural Plastics (CSP) in Fort Wayne, Ind., for construction into the actual bed. The company, a subsidiary of Teijin, makes a wide variety of composite and plastic parts for the car industry, including body panels for the C7 Chevy Corvette. The rectangular sheets are cut to shape and stacked up at a giant stamping press. Robots pick up sheets and slide them onto a conveyor that goes into a large oven. The heat softens the parts so they can be stamped. The large primary bed parts such as the base are stamped by CSP's enormous 3,600-ton press, and the smaller ones go through a 1,000-ton press. Each press can do different parts using different stamping dies, and CSP switches between dies to produce different batches of parts. After stamping, the parts roll out mostly ready for assembly, but there are rough edges that are trimmed off by water-jet cutters. These cutting machines also create holes for fasteners and for parts such as tie-down hooks and lights. The stamping process also provides the carbon fiber bed with a unique Easter egg. On the bottom of the base of the bed, there are two words: "Connors Way." This is a tribute to Tim Connors, who was the chief engineer of manufacturing at GM and a strong proponent of the carbon fiber bed. He was tragically killed in a motorcycle crash a few years ago. The words were added to honor him, and they were fortunately approved for production. There are some components to the bed that aren't stamped from the flat sheets of material.

GM CEO to meet with U.S. lawmakers over job cuts

WASHINGTON — General Motors Co Chief Executive Mary Barra plans to visit Capitol Hill next week to discuss the company's plans to halt production at five plants in North America next year and cut up to 15,000 jobs, two congressional aides said on Friday. GM has come under harsh criticism from lawmakers from both major political parties, and from President Donald Trump, since Monday when it announced the biggest restructuring for the U.S. No. 1 carmaker since its bankruptcy a decade ago. Barra is expected to meet with lawmakers from Michigan and Ohio, where GM plans to shutter three plants, as well as senior leaders in Congress. GM did not immediately comment. Barra has been calling lawmakers this week to explain the decision to end production. Trump has threatened to revoke subsidies for GM. The Detroit automaker plans to halt production next year at three assembly plants: the Lordstown small-car factory near Youngstown, Ohio; the Detroit-Hamtramck complex in Detroit; and the Oshawa, Ontario, assembly complex near Toronto. It will also stop building several models now assembled at those plants, including the Chevrolet Cruze, the Chevrolet Volt hybrid, the Cadillac CT6 and the Buick LaCrosse. Additionally, GM plans to shutter the Warren transmission plant outside Detroit and a plant that makes electric motors and drivetrains outside Baltimore, Maryland. The Cruze compact car will be discontinued in the U.S. market in 2019, although GM may continue building it in Mexico for other markets, Barra said. Reporting by David Shepardson. Related Video: