2020 Gmc Acadia Slt on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Next Chevy Silverado could get this built-in tailgate step

General Motors just received patent approval for a tailgate step in a pickup bed. And given the timing, don't be surprised if you see this on the upcoming 2019 Silverado pickup (not the mention its GMC Sierra twin), expected to arrive in late 2018. According to the patent, granted in December of last year, the whole mechanism is housed in the tailgate assemble. The magic happens when a portion of the top half of the tailgate swings down and a step folds out. There's also a handle that locks into position to help climb up into the bed. As trucks get bigger and taller over the years, it gets harder and harder to access the cargo bed. Ford's solution with the 2009 F-150 was a step that slides out from the end of the tailgate. Back then, Chevy made an ill-advised ad highlighting the feature for Ford. And while Howie Long mocked the F-150's "man step" Ford saw almost a third of its trucks with the option in the first year. The GM design seems to improve on Ford's idea as it appears to be wider and has a back to the lower step. That is, you don't have to worry about stepping through the ladder-rung design as on the F-150. Ford's tailgate step later spread to the F Super Duty, and other cargo access assists have proliferated through the truck world. On the most recent redesign, the Chevrolet Silverado took a trick from the Avalanche and added cutouts to the corners of the rear bumper that act as a foothold. Ford also offers a deployable side step, Chevrolet has running boards that scoot rearward with a kick of the boot, and Ram offers fixed wheel-to-wheel side rails. Nissan is in on the game too, with an optional folding step that tucks under the rear bumper. We don't expect Chevrolet to comment on when or if we'll see this feature in the showrooms. But given that engineers are already hard at work on the next Silverado and the timing of this patent lines right up with the new truck's development cycle, we'll be disappointed if this patent stays in the file cabinet. Related Video:

GM diesel pickups first to undergo extra EPA, CARB testing

The effects of Volkswagen's long-running diesel emissions evasion are starting to spill over to other automakers, but General Motors is taking things in stride. The 2.8-liter, four-cylinder Duramax in the 2016 Chevrolet Colorado and GMC Canyon is the first engine to get extra scrutiny by the Environmental Protection Agency and the California Air Resources Board, Automotive News reports. Rather than just the usual in-lab test, it's also being checked on the road. However, the extra evaluation shouldn't have any impact on when the trucks with his mill hit dealers later this fall. "We're in our final stages of the EPA certification, and our launch is on track," Chevy spokesperson Otie McKinley tells Autoblog. The four-cylinder diesel in the trucks makes 181 horsepower and 369 pound-feet of torque, and the automaker is touting low NOx production. In the announcement for the Colorado's specs, the company calls it "the cleanest diesel truck engine ever produced by General Motors." The tech includes exhaust gas recirculation to lower combustion temperatures and improve emissions. There's also a urea tank like on the bigger diesels for full-size trucks, and it gets refilled in time with oil changes. An indication on the instrument panel lets drivers know when that's needed, too. Even with the more demanding testing, the company doesn't seem too worried about the four-cylinder passing. "Part of our development process is on-road and off-road [laboratory] testing," Scott Yackley, Chevy Trucks assistant chief engineer, said to Automotive News. In the wake of the VW scandal, the EPA has pledged more rigorous testing. Before, on-road emissions evaluations were largely limited to heavy-duty vehicles, but the agency has decided to apply the checks more often to other models. There's also now greater cooperation with Canadian authorities.