2014 Gmc Acadia Sle on 2040-cars

Auto blog

Torque time | 2017 GMC Sierra HD First Drive

It's not the truck that counts, it's how you use it. It's the heavy stuff you fit in its bed or the extremely heavy stuff that gets hooked up to the tow hitch. The ATV, the Jet Skis, the trailer with more square footage than a Greenwich Village apartment. Perhaps you need to get Seabiscuit or, uh, Mr. Ed to wherever they need to gallop next. In our case, there's a pair of very serious-looking snowmobiles perched atop the bed of a GMC Sierra. They spread out as wide as the extended tow mirrors, and their back halves are dangling precariously beyond the truck. Sterling Archer would be giddy; I'm a little nervous. But only because canyon roads and wide vehicles with a high center of gravity go together like peas and custard. The added weight is no sweat at all. That's because this is the 2017 GMC Sierra HD Denali, a truck with the sort of enhanced power, torque, suspension, and stopping capability expected of a heavy-duty pickup. And for this year, the power and torque get a serious bump courtesy of a new 6.6-liter Duramax turbodiesel engine reengineered from almost the ground up with 90 percent new parts. It's quieter and more efficient and it emits less, while most importantly producing 445 horsepower and 910 pound-feet of torque. That's up from 397 and 765, respectively. Chevy fans will note that the same engine is also available in the updated 2017 Silverado HD. Now, for those keeping score at home, that horsepower is best-in-class but the torque number still falls short of the new Ford Super Duty and its Power Stroke diesel V8's 925 lb-ft. Aw shucks. For the record, GM's engineers didn't seem too concerned that they weren't able to eke out an extra 16 torques just to say they're No. 1. "We wanted to first meet emissions and then deliver the maximum horsepower and torque we could, and deliver it over the widest usability range possible," said chief engineer Eric Stanczak. And let's be honest here, 910 pound-feet is herculean, and once again, a jump of 145 lb-ft. Or one Subaru Impreza's worth. Or 110 more than the best Ram can do on a 2500, and its Cummins turbodiesel's 800 pound-feet was eye-popping not too long ago. (The Ram 3500 maxes out at 900 lb-ft with the right transmission.) Ah, but here's the rub. That Cummins-equipped Ram 2500 can still tow more weight according to SAE-compliant measurements – 17,510 pounds for a Ram crew cab with a short bed versus 13,000 in the similar Sierra 2500. The Ford F-250 can manage 15,000.

GMC Syclone spools up a storm on Jay Leno's Garage

A storm was brewing on American roads in the early 1990s. That's when Detroit's automakers were producing some of the hottest performance trucks ever devised – models like the Ford Lightning, GMC Typhoon, and its flyweight pickup sibling, the GMC Syclone. Jay Leno just happens to have one of the latter in his garage, and took it out to showcase in this latest video segment. The Syclone was an exercise in absurdity, and could not only trounce any other pickup on the road, it could outrun anything else GM made and just about anything else on the road – beating Ferraris and Porsches off the line. In a pickup, for crying out loud. The kicker is that its engine wasn't such a monster, either: under the hood sat a 4.3-liter turbocharged V6 pumping out what would seem by today's standards to be an adequate 280 horsepower and 350 pound-feet of torque. Even the smaller of the EcoBoost V6s available in today's Ford F-150 produces more than that. But in a lightweight, compact pickup, those figures were enough to propel the Syclone to 60 in 4.3 seconds and run the quarter-mile in 13.6 seconds. Long before the dune-jumping Ford F-150 SVT Raptor or even the Viper-powered Dodge Ram SRT-10, GM made fewer than 3,000 Syclones based on the compact Sonoma (sister to the Chevy S-10) and another 4,700 of the Typhoon, which was mechanically similar but more practical (albeit heavier) wagon bodywork from the Jimmy. But as Jay aptly points out, the Syclone was the one you wanted. Scope it out in the ten-minute video clip above.

GMC has received 65,000 Hummer EV orders so far

The GMC Hummer pickup truck only just went on sale, and already there's word from company brass that demand is higher than expected. According to a report from CNBC, Duncan Aldred, global vice president of GMC, said the automaker has received more than 65,000 combined orders for the current electric truck and upcoming SUV. What's more, the number of customers converting reservations into orders is humming along at 95%, which is also higher than the company projected. "Production’s actually slightly ahead of plan and weÂ’re putting things in place now to actually expedite that as well, so we can deliver these reservations quicker than we originally thought," Aldred said, adding that new orders placed today probably won't result in a delivered vehicle until 2024. "WeÂ’re doing all the studies on that and weÂ’re confident we can go a lot quicker than we originally thought," Aldred said, "But it still means a reservation now probably means delivering in Â’24." The version of the Hummer pickup that's currently being built is the highest-spec Edition 1 model. That truck ran at least $110,295, but since it's already sold out, new customers will be looking at Hummer EV 3X that starts right around the $100,000 mark before any optional equipment is added (and assuming you can find a dealer that won't try to jack up the price). At some unspecified point in the next year or so, GMC will start building a lower-cost Hummer 2X for $89,995. A year or so later, the  $79,995 Hummer EV 2 will make its debut. Related video: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings.