2000 Ford Windstar, Police Seizure on 2040-cars

Auto blog

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).

2014 Ford Fiesta ST

Concentrated ST Formula Proves Just As Potent
I'm not the jealous type... usually. But I will fully admit to being somewhat of a Pouty Polly when I read executive editor Chris Paukert's report after driving the then-new 2013 Ford Focus ST through the impossibly pretty southern French Alps region last June. I feel like a broken record saying this yet again, but hot hatchbacks hold a special place in my heart. And while I'm always giddy to drive any sort of small, turbocharged three- or five-door at home in Detroit, my jealousy was indeed piqued after hearing Paukert tell about the challenging yet breathtaking roads he encountered while driving the flamin' yellow Focus. You know, the sort of roads that, from above, look like carelessly drizzled lines of icing on the frosted Alpen caps.
Several months later, I found myself piloting a Focus ST just west of metro Detroit, pitting it head-to-head against one of Autoblog's perennial favorite cars, the Volkswagen GTI. It was fantastic - enough so that I fully stand behind my statement that in terms of balls-out performance, the Focus ST cannot be beat as far as today's front-wheel-drive hatches are concerned.

Ford won't be releasing GT500 lap times for the 'Ring, or any other car

Trucks have towing capacity, EVs have driving range and performance cars have Nürburgring lap times. What do all three have in common? They should all be taken with a grain of salt. Currently, there is no sanctioned way to record lap times or verify production-spec cars - a lesson we recently learned with the 2015 Nissan GT-R Nismo - and until there is a way to do so (and there probably never will be), we'll never officially know the actual time it took for Ford to lap the 'Ring with its ultra-powerful Shelby GT500.
After posting a Ford-made video of a 2013 GT500 running around the 'Ring, the guys over at SVTPerformance.com (an enthusiasts forum not affiliated with Ford or SVT) wanted more answers. They got in touch with Ford's Global Performance Vehicle Chief Engineer Jamal Hameedi, who said until there is a way to verify the times and inspect the cars, Ford will not get involved with lap-time wars. In the email, Hameedi pointed out that the 'Ring is a useful tool in that it allows a wide spectrum of track conditions, but until there is a governed way to record times, there is no way to accurately compare cars head-to-head.
And as much as some may not like it, Hameedi speaks the truth. It really isn't possible to compare times from one car to another, unless those cars were lapping the same track at the same time with the same driver. Not that any of this means there won't be continuous wars by fans and manufacturers alike... in other words, feel free to voice your opinions in the Comments below.