2004 Ford Thunderbird Convertible Less Then 10,000 Actual Miles on 2040-cars

Auto blog

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).

Car Stories: Owning the SHO station wagon that could've been

A little over a year ago, I bought what could be the most interesting car I will ever own. It was a 1987 Mercury Sable LS station wagon. Don't worry – there's much more to this story. I've always had a soft spot for wagons, and I still remember just how revolutionary the Ford Taurus and Mercury Sable were back in the mid-1980s. As a teenager, I fell especially hard for the 220-horsepower 1989 Ford Taurus SHO – so much so that I'd go on to own a dozen over the next 20 years. And like many other quirky enthusiasts, I always wondered what a SHO station wagon would be like. That changed last year when I bought the aforementioned Sable LS wagon, festooned with the high-revving DOHC 3.0-liter V6 engine and five-speed manual transmission from a 1989 Taurus SHO. In addition, the wagon had SHO front seats, a SHO center console, and the 140-mph instrument cluster with mileage that matched the engine. When I bought it, that number was just under 60,000 – barely broken in for the overachieving Yamaha-sourced mill. The engine and transmission weren't the only upgrades. It wore dual-piston PBR brakes with the choice Eibach/Tokico suspension combo in front. The rear featured SHO disc brakes with MOOG cargo coils and Tokico shocks, resulting in a wagon that handled ridiculously well while still retaining a decent level of comfort and five-door functionality. I could attack the local switchbacks while rowing gears to a 7,000-rpm soundtrack just as easily as loading up on lumber at the hardware store. Over time I added a front tower brace to stiffen things a bit as well as a bigger, 73-mm mass airflow sensor for better breathing, and I sourced some inexpensive 2004 Taurus 16-inch five-spoke wheels, refinished in gunmetal to match the two-tone white/gunmetal finish on the car. That, along with some minor paint and body work, had me winning trophies at every car show in town. And yet, what I loved most about the car wasn't its looks or performance, but rather its history. And here's where things also get a little philosophical, because I absolutely, positively love old used cars. Don't get me wrong – new cars are great. Designers can sculpt a timeless automotive shape, and engineers can construct systems and subsystems to create an exquisite chassis with superb handling and plenty of horsepower. But it's the age and mileage that turn machines into something more than the sum of their parts.

Martini Mustang is a 'what if moment' gone right

Feast your eyes on a masterpiece. This is Steve Strope's Ford Mustang in the classic fastback bodystyle, and as you'll notice, it sports the signature colors of Martini Racing, a livery that's as legendary as any Gulf Racing-styled car. But the red, white and blues of the Martini stripe down this Mustang's middle tell only a very small part of the story, in the latest video from Petrolicious.
What would you guess is under the hood? A 289-cubic-inch V8? Maybe a 302, or some absurd Ford crate engine? Maybe Strope went all Tokyo Drift - he's actually responsible for the "Hammer" Plymouth Satellite driven by Vin Diesel at the end of the movie - and found an RB26DETT to drop into the pony car? You'd be wrong on all counts.
This mad, mad man somehow finagled a Ford-Lotus engine from a 1966 Indianapolis 500 car into the Mustang's engine bay. Yes, a Mustang with an engine designed for a 160-mile-per-hour, open-wheel racecar. That's like someone in 40 years dropping McLaren's 2.4-liter V8 from the MP4-28 into a Scion FR-S. It'd just make a monster.