1960 Thunderbird Last And Highest Serial Number Produced For 1960 Production on 2040-cars

Auto blog

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).

Ford Mustang returning to Australia in 2016

Australia's Herald Sun newspaper has reported that the next-generation Ford Mustang is heading Down Under in 2016, just as Ford is hanging the "Closed for Good" sign on its Australian manufacturing operations and sending the Falcon to its grave. Ford hasn't offered any official word on the matter, but the paper says that Ford's global VP of sales and marketing, Jim Farley, is flying to Australia to make the announcement himself.
While Ford converted Mustangs in the early 2000s from left-hand to right-hand drive for the Australian market and then sold them at high prices, it's been almost five decades since Ford imported a dedicated right-hand-drive Mustang to Oz. The arrival of the global model specifically made for places like Australia and the UK means Ford will also be able to offer them at better prices than the converted models; the Herald Sun says the price is expected to be "close to $50,000."
And that's for one of the "V8 performance models," which are the only ones Australia will get; Ford apparently won't send the turbocharged four cylinder or the V6. The Aussies could find out in a month from now whether this rumor is true. We will all find out what this Mustang fuss is about when the car debuts at next year's New York Auto Show.

Ford Mustang GT350 drops some camo

Now that we've poured over the 2015 Ford Mustang in its standard form, it's time to look ahead. We already knew (and heard - literally) that Ford was working on a higher-performance version of its 'Stang to replace the Shelby GT500, and earlier reports have stated that it will simply be called the GT350.
We don't have a ton of detail to go on, but this latest set of spy photos clearly shows a hood-mounted air scoop, which suggests a forced-induction powerplant is under the hood. However, this disagrees with earlier reports that the GT350 will be all motor, using a naturally aspirated engine to send massive horsepower to the rear wheels. Our spies also point out the functional vent aft of the front wheels to allow for better airflow, and the massive quad exhaust pipes can be seen, clear as day.
Expect to see the Mustang GT350 in April, when it debuts at the New York Auto Show in conjunction with the Pony's 50th anniversary. In the meantime, have a look at our gallery above to see the latest shots of the hot Mustang out testing.