2009 Ford Taurus Limited Sedan 4-door 3.5l on 2040-cars

Auto blog

Ford Mustang Mach-E fails Sweden's moose test

The infamous moose test has claimed another casualty. This time it's the Ford Mustang Mach-E AWD Long Range, which was tested in an electric four-way alongside the Tesla Model Y, Hyundai Ioniq 5 and Skoda Enyaq iV (an electric utility vehicle closely related to the Volkswagen ID.4 that is sold in the United States). According to the Swedish testers at Teknikens Varld, Ford's electric car not only failed to hit the speed necessary for a passing grade, it didn't perform well at slower speeds, either. To pass the outlet's moose test, a car has to complete a rapid left-right-straight S-shaped pattern marked by cones at a speed of at least 72 km/h (44.7 miles per hour). The test is designed to mimic the type of avoidance maneuver a driver would have to take in order to avoid hitting something that wandered into the road, which in Sweden may be a moose but could just as easily be a deer or some other member of the animal kingdom elsewhere in the world, or possibly a child or car backing into the motorway. Not only is the maneuver very aggressive, it's also performed with weights belted into each seat and more weight added to the cargo area to hit the vehicle's maximum allowable carrying capacity. The Mustang Mach-E only managed to complete the moose test at 68 km/h (42.3 mph), well below the passing-grade threshold. Even at much lower speeds, Teknikens Varld says the Mach-E (which boasts the highest carrying capacity and was therefore loaded with more weight than the rest of the vehicles tested in this quartet) is "too soft in the chassis" and suffers from "too slow steering." Proving that it is indeed possible to pass the test, the Hyundai and Skoda completed the maneuver at the 44.7-mph figure required for a passing grade and the Tesla did it at 46.6 mph, albeit with less weight in the cargo area. It's not clear whether other versions of the Mustang Mach-E would pass the test. It's also unknown if Ford will make any changes to its chassis tuning or electronic stability control software, as some other automakers have done after a poor performance from Teknikens Varld, to improve its performance in the moose test. Related video:

Ford and Chrysler reducing summer plant shutdowns

Most domestic automaker assembly plants traditionally take a couple of weeks off during the summer. The shutdowns give each plant time for much needed repairs and maintenance, and in some cases, help better align production with demand. Not this year, though, as demand for many models is outstripping what Ford, Chrysler and General Motors plants can produce.
Ford has announced that it will shorten its annual summer shutdown for most North American plants from two weeks to one. The shorter shutdown will increase the carmaker's annual North American production by 40,000 units on top of the 200,000 extra units that it was already planning to produce this year versus last. Automotive News reports that Ford produced 2.8 million vehicles on this continent in 2012, and that output this year has already increased 13 percent through April.
Chrysler, meanwhile, is also operating at full tilt and plans to run some plants through the summer with no shutdown at all. Those not getting a break include Jefferson North where the Jeep Grand Cherokee and Dodge Durango are assembled, Toledo North that will assemble the new Cherokee, and Conner Avenue, home of SRT Viper production. Other assembly plants will be down for a single week, while all of Chrysler's engine and transmission plants except one in Indiana will continue operating with no shutdown this summer.

Ford celebrating 80 years of Aussie utes as it prepares to shutter Oz manufacturing

Ford is ending Australian production after 90 years in 2016, and with it may go perhaps the most iconic vehicles in its auto market - the ute. Car-based pickup trucks like the Ford Ranchero and Chevrolet El Camino were always more of a curiosity than a true market force here, but in Australia, they have long proven hugely popular.
As the legend goes, Ford invented the niche after a farmer's wife had asked Ford Australia's managing director for a more utilitarian car. Her request was simple: "My husband and I can't afford a car and a truck but we need a car to go to church on Sunday and a truck to take the pigs to market on Monday. Can you help?"
Ford's design team came up with a two-passenger, enclosed, steel coupe body with glass windows and a steel-paneled, wooden-frame load area in the rear. The sides of the bed were blended into the body to make it look more unified, and to keep costs down, the front end and interior were based on the Ford Model 40 five-window coupe. Power came from a V8 with shifting chores handled by a three-speed manual. Within a year, the new vehicle was ready, and production began in 1934. Lead designer Lewis Bandt christened it the coupe-utility.