1993 Ford Taurus Sho Sedan 4-door 3.2l * 1994 3.0 Engine Manual **2 Car Package* on 2040-cars

Auto blog

Want a V8 on the cheap? Buy a work truck

In case you didn't notice, V8 cars have gotten pretty expensive. If you want a modern muscle car like the Dodge Challenger R/T, Ford Mustang GT, or Chevy Camaro SS, you'll need between $34,000 and $38,000 for a stripped out example of one. The cheapest of those is the Challenger, and the priciest is the Camaro. These are also the cheapest V8 cars the companies offer. But if you absolutely have to have a V8 for less, there is an option, work trucks. As it turns out, all of the Big Three offer their most basic work trucks with V8s. And because they're so basic, they're pretty affordable, especially when sticking with the standard two-wheel drive. A Ram 1500 Tradesman with a V8 can be had for as little as $29,840, which is a little more than $4,000 less than a Challenger R/T. For a bit more at $30,275, you can have a Chevy Silverado W/T, almost $8,000 less than a Camaro SS. The most expensive is the V8 Ford F-150 starts at a starting price of $30,670, which is a bit over $5,000 less than the Mustang. Of course you'll be in an ultra bare bones vehicle with few comforts, and the price will go up if you add stuff, but we're bargain hunting here, and sacrifices are sometimes necessary. Besides, what you lose in comfort, you gain in loads of cargo space and towing (try to look at the bright side). Also, as a side note, all three trucks are available with optional electronic locking rear differentials. At the discounted price of these trucks, you still get a heaping helping of power. The most potent of the trio is the Ram 1500 Tradesman with 395 horsepower and 410 pound-feet of torque generated by a 5.7-liter V8. Compared with the Challenger R/T, the Ram is up by 20 horsepower and they're tied for torque. The value proposition is even more stark between the two vehicles when looking at the price per horsepower. Each pony in the Ram costs $75.54, while the Challenger charges you $90.91. The Challenger is also more expensive per horsepower than its close competitors. The F-150's 5.0-liter V8 is just barely behind the Ram with 395 horsepower and 400 pound-feet of torque. That's still more power than the Challenger, and it matches the torque of the 2017 Mustang GT. On the down side, it still would be down 20 horsepower on that same 2017 Mustang, and it's behind by 60 horsepower and 20 pound-feet on the new 2018 Mustang GT. The F-150 also just edges out the Mustang in the dollar per horsepower measure.

Ford Focus ST checks into Jay Leno's Garage

In a change of pace from the high-end vehicles that often appear in Jay Leno's Garage, Ford sends its hottest hatchback (in the US, at least), the 252-horsepower Focus ST, to be featured on Leno's show. Accompanying the five-door hatch is its chief engineer, Jamal Hameedi.
Riding on stylish 18-inch wheels with summer tires and with a spoiler that doubles as a lunch tray, Hameedi and Leno walk us through the finer points of what makes the ST special, which also includes bigger brakes, torque vectoring, a manual transmission and, of course, 252 hp and 270 pound-feet of torque from the 2.0-liter EcoBoost four-cylinder engine, which is made possible by 21 psi of turbocharged boost.
Watch the video below to see what Leno thinks of the global Focus ST.

Ford 3D-printing Mustang out of chocolate and candy for Valentine's Day

Is your beloved in love with the new 2015 Ford Mustang? Do they like chocolate (that's a trick question - everyone likes chocolate)? Are they a bit of a futurist? Then this Hallmark holiday, you need to get them this Ford Mustang, 3D-printed in sweet, delicious chocolate.
Ford is teaming with 3D Systems' Sugar Lab in LA to produce the super-accurate pony car confections in both chocolate and sugar candy varieties. The process kicked off with a CAD rendering of the 2015 Mustang, which was then programmed into the 3D printer. After a bit of work from the machine, a four-inch long, two-inch tall Mustang was the result. Why the tieup with 3D Systems, though?
"We wanted to create something fun to show that while 3D printing made these edible Mustangs, manufacturing-level 3D printing was used in the development of Ford's all-new sports car," said Paul Susalla, Ford's supervisor of 3D printing.