1967 Ford Shelby Gt500 on 2040-cars

Auto blog

Want a V8 on the cheap? Buy a work truck

In case you didn't notice, V8 cars have gotten pretty expensive. If you want a modern muscle car like the Dodge Challenger R/T, Ford Mustang GT, or Chevy Camaro SS, you'll need between $34,000 and $38,000 for a stripped out example of one. The cheapest of those is the Challenger, and the priciest is the Camaro. These are also the cheapest V8 cars the companies offer. But if you absolutely have to have a V8 for less, there is an option, work trucks. As it turns out, all of the Big Three offer their most basic work trucks with V8s. And because they're so basic, they're pretty affordable, especially when sticking with the standard two-wheel drive. A Ram 1500 Tradesman with a V8 can be had for as little as $29,840, which is a little more than $4,000 less than a Challenger R/T. For a bit more at $30,275, you can have a Chevy Silverado W/T, almost $8,000 less than a Camaro SS. The most expensive is the V8 Ford F-150 starts at a starting price of $30,670, which is a bit over $5,000 less than the Mustang. Of course you'll be in an ultra bare bones vehicle with few comforts, and the price will go up if you add stuff, but we're bargain hunting here, and sacrifices are sometimes necessary. Besides, what you lose in comfort, you gain in loads of cargo space and towing (try to look at the bright side). Also, as a side note, all three trucks are available with optional electronic locking rear differentials. At the discounted price of these trucks, you still get a heaping helping of power. The most potent of the trio is the Ram 1500 Tradesman with 395 horsepower and 410 pound-feet of torque generated by a 5.7-liter V8. Compared with the Challenger R/T, the Ram is up by 20 horsepower and they're tied for torque. The value proposition is even more stark between the two vehicles when looking at the price per horsepower. Each pony in the Ram costs $75.54, while the Challenger charges you $90.91. The Challenger is also more expensive per horsepower than its close competitors. The F-150's 5.0-liter V8 is just barely behind the Ram with 395 horsepower and 400 pound-feet of torque. That's still more power than the Challenger, and it matches the torque of the 2017 Mustang GT. On the down side, it still would be down 20 horsepower on that same 2017 Mustang, and it's behind by 60 horsepower and 20 pound-feet on the new 2018 Mustang GT. The F-150 also just edges out the Mustang in the dollar per horsepower measure.

Feds Probe Power Steering In 938,000 Ford Midsize Cars

U.S. safety regulators are investigating complaints that the power-assisted steering can suddenly fail on three Ford midsize car models. The probe covers 938,000 Ford Fusion and Lincoln MKZ cars from the 2010 through 2012 model years, as well as the 2010 and 2011 Mercury Milan. The National Highway Traffic Safety Administration says it has received 508 complaints alleging that the cars lost power-assisted steering, causing increased steering effort. Four complaints say the problem caused crashes, but no injuries were reported. The agency says in documents posted Monday on its website that in many cases, a warning message appeared as the failure happened. Restarting the car corrected the problem in some cases, but the problem returned in others. The agency says it will check the scope and frequency of a problem. It could seek a recall. Ford says it's cooperating with the probe. Shares of Ford Motor Co. rose 6 cents to $14.65 in morning trading Monday. Its shares are down 14 percent over the past year. Related Gallery Our Favorite Hot And Sporty Cars For 2015 Recalls Ford Lincoln NHTSA Ford Motor Company power steering mercury milan investigation

Experts wonder if aluminum F-150 gives Ford a real advantage

There's no doubt that Ford is taking a risk in producing the body of its upcoming new F-150 pickup truck in aluminum. What is up for debate, however, is whether aluminum was a wise risk to take in the first place. Wards Auto took the opportunity to poll some experts on the subject of aluminum versus steel in the automotive sector, with somewhat unsurprising results.
Richard Schultz, a project consultant at Ducker Worldwide, which bills itself as "a leading aluminum industry consultant (though they also deal in steels), suggests that the potential drawbacks to aluminum - higher costs, lower supply - aren't really impediments to the auto industry's increased acceptance of the lightweight metal.
Similarly, Randall Scheps, global automotive marketing director for Alcoa, a massive aluminum producer, counters claims that aluminum is less safe for vehicle occupants, suggesting that the use of aluminum can actually increase safety as it could potentially allow for larger vehicles with more crush space than steel.