2006 Ford F450 Flatbed 9-ft Heavy Duty Powerstroke Diesel F-550 F-350 Low Miles on 2040-cars

Auto blog

Shelby to auction 2012 GT350 No. 1 in Vegas

With Shelby preparing to wind down production of its brutal GT350, a 624-horsepower Mustang that's meant to go up against the Roush Stage 3 in the world of tuned Ford ponycars, the Las Vegas-based tuner is looking to give back to one lucky customer. It'll auction off the very first GT350 ever produced, at the 2013 Barrett-Jackson auction in Las Vegas, a three-day event that runs from September 26 through September 28.
The GT350 is a monster, with a 5.0-liter, supercharged V8 that's been tuned well past 600 horsepower in a time when Ford's own Shelby-branded GT500 barely reached 550 horsepower. The GT350 is much louder than Ford's effort, too, both visually and audibly. The wide body look isn't what we'd call conventional, but on a car that sounds and goes like this, something extreme is needed. According to Shelby American's vice president of production, Gary Davis, "Carroll was very excited about the new wide body option, so that was included on this car. It's the first 2012 GT350 serial number from our anniversary year. It is a very special car." Wilwood brakes, a massaged suspension, and some very fat, sticky tires add to the Shelby experience.
This particular GT350 will be lot number 750, and will cross the Barrett-Jackson stage on Sunday, September 28.

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).

Holy crime-fighting Ford F-150, Batman!

What would Batman drive for his weekly trips to Home Depot for the bits and pieces needed to keep his lair deep below Wayne Manor in tip-top condition? Certainly not the Batmobile - there's no way a 4x8 sheet of plywood will fit between the wheel wells, not to mention the fact that jet turbine engines have an unfortunate tendency to set trailers on fire when towing...
No, what Batman needs is a pickup truck. The boys from Ford teamed up with Galpin Auto Sports to build just such a machine, and it has just debuted at Comic Con. Designed by Jared Barris, grandson of the legendary kustomizer George Barris, the 2012 F-150 pickup you see here, dubbed Crime Fighter, is painted Tuxedo Black with Ferrari Red highlights and is affixed with fins on each side of the truck bed. It's nothing if not unique.
Well, it's at least unique for now. According to Ford, Galpin in Southern California is willing to take orders for customers looking to don a cape and hit the town for a night of crime-fighting action. Or trips to Home Depot. Check out our high-res image gallery and then scroll down for the official description from Ford. We're waiting for details such as pricing and build time from Ford, and we'll update this post if and when we hear back.