Ford Mustang Svt Cobra Convertible 2-door on 2040-cars

Auto blog

Ford starting up 2.0L EcoBoost engine production in Ohio

Joe Hinrichs, Ford's President of The Americas (pictured above), announced today that in late 2014, the automaker will be building the 2.0-liter EcoBoost four-cylinder at its Cleveland Engine Plant, a move requiring a $200-million investment and the hiring of 450 new employees. European-built Ford products will continue to source this engine from the Valencia, Spain plant where all of these EcoBoost four-cylinder engines are currently built, and the new Cleveland engines will be used for all North American-made models.
Ford is planning to build its popular EcoBoost engines regionally to maximize production capacity and meet customer demand. Last year, Ford sold 334,364 vehicles with EcoBoost engines in the US alone, and that number is expected to swell to more than 500,000 by the end of this year, with global sales expected to total 1.6 million. By 2015, Ford says that 95 percent of its nameplates will offer an EcoBoost engine.
One such vehicle that could be adding an EcoBoost engine, according to Automotive News, is none other than the 2015 Ford Mustang. The report says that Ford could use either the 2.0-liter EcoBoost or an upcoming 2.3-liter EcoBoost in the sixth-generation pony car.

Ford recalls more than 550,000 trucks and SUVs for various safety issues

Ford announced safety recalls for its current F-150 pickup along with several Ford and Lincoln crossovers early Wednesday. The recalls cover more than 550,000 vehicles and address various safety defects, ranging from a fire hazard to potential loss of braking power.  The most far-reaching of the recalls covers approximately 550,000 examples of the 2015-2018 Ford Edge and 2016-2018 Lincoln MKX, which may have been assembled with defective front brake jounce hoses (also commonly referred to as "flex lines"). These hoses run from fixed points on the chassis to the individual front brake calipers. Defective hoses could potentially rupture, allowing brake fluid to leak and resulting in a loss of braking function. Ford will replace the components in question with revised parts.  The next-largest recall is for roughly 3,000 2020 Lincoln Corsair crossovers. The affected models may have been assembled without proper clearance between their rear suspension springs and toe link brackets. The components could potentially make contact, wearing down the protective coating on the rear coil springs, allowing corrosion to occur over time. This corrosion could eventually lead to a failure of the spring. If this happens while the vehicle is being driven, it could result in a sudden change to the vehicle's handling characteristics, and the spring fragments could potentially cause further damage to the car or surrounding traffic.  Ford says owners will be notified that their Corsairs need to be inspected; if there is not adequate clearance between the rear suspension components, Ford's service technicians will remove material from the toe link bracket to allow for operation without contact.  The final (and by far the smallest) recall is for the 2020 F-150. Some units may have left the factory with the incorrect retention nut on the hot lead to the starter motor. Ford says it can cause increased heat generation or electrical arcing, which could potentially result in a fire. Ford says this issue is limited to just a few hundred examples sold in the United States. Dealers will inspect the vehicles and replace the nut if necessary.       

Help make Lego Icon Bronco a reality [UPDATE]

The Lego Ideas process is a pretty neat concept. The website allows anyone to propose a future kit, and if the project gathers 10,000 supporters within a certain amount of time, then the company investigates building it. The creator even gets a cut of the sales. We saw the operation at work last year with a very cool looking Corvette kit that hasn't hit the next stage quite yet. Now, another creator going by the username Legohero1966 has a fantastic looking replica of the Icon 4X4 Bronco hoping for support. The maker nails the boxy, brawny look of the Icon take on the classic Ford Bronco, and the Lego kit even gets the color pretty close. The miniature SUV also features a visible suspension, a removable top and, according to the description, a reel for the winch is hidden in the bumper. Underneath the body, this model even does a pretty good job of replicating the powertrain. As is expected by these kits, the hood, doors and hatch all open; on this one the spare tire carrier even moves out of the way, too. As of this writing, the Icon Bronco kit only has a little over 400 supporters, and that's a long way from the goal. If you like what you see, give the proposal a closer look on Lego Ideas. UPDATE: The original creator of the Icon Bronco kit, Paul Kim, has advised Autoblog that this Lego Ideas proposal was created without his consent, and he has reported the problem there. You can view more pictures of the Bronco and more of Kim's work, here. Featured Gallery Lego Icon 4X4 Bronco Proposal Design/Style Toys/Games Ford SUV Off-Road Vehicles Performance Classics Lego Ford Bronco icon icon 4x4 icon bronco lego ideas