2005 Ford Mustang "supercharged"convertible Original 40k Miles on 2040-cars

Auto blog

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).

Ford shutters Genk assembly plant in Belgium

Ford has become the latest automaker to close one of its European assembly plants. The facility in question is located in the Belgian city of Genk and has been in operation since the early '60s when it started building the Taunus, Ford's first mass-produced, front-drive model. As part of the plan first announced over two years ago, the Genk Body & Assembly Plant is now closing its doors after half a century in the business and over fourteen million vehicles built. Although the plant itself employed some 5,000 workers, once you take into account the suppliers built up around the plant, the overall impact on employment in the area edges closer to 12,000. Genk Body & Assembly had until recently been tasked with producing the Mondeo sedan (which in its current iteration we know as the Fusion) as well as the S-Max and Galaxy minivans. Production of the Mondeo shifted in 2013 to the company's plant in Valencia, Spain, which also handles the Kuga crossover and Transit Connect cargo van, and will soon take over the minivans from Genk as well. The move follows a similar decision undertaken by General Motors to close the Opelwerk plant in Bochum, Germany. It also reflects a scaling down of automobile production in Belgium specifically: although Audi still manufacturers in Brussels and and Volvo in Ghent, Opel closed its plant in Antwerp in 2000 and Renault ceased production in Vilvoorde back in '97. However Ford still maintains its famous proving ground half an hour to the north in Lommel, Belgium. News Source: AutovisieImage Credit: Kristof Van Accom / AFP / Getty Plants/Manufacturing Ford plant ford s-max ford galaxy

Ford wants to double hybrid offerings by 2020

The Blue Oval is looking for folks on the other side of this Big Old Sphere to get on board with its hybrid offerings. Ford executive Raj Nair, speaking at the Detroit Auto Show this week, said the US automaker wants to double the number of hybrids models it offers by the end of the decade, Reuters reports. Details of what that actually means is anyone's guess, as it was unclear how many of those models would be in the US and how many would be overseas. That said, Nair did say that prospective customers in regions such as China and Europe would drive the expansion of offerings. Ford got off to a great start in the US last year on its hybrid sales, but then tailed off towards the end of 2013. Ford more than doubled its green-car sales in 2013 to almost 88,000 units. In that number were more than 37,000 Fusion Hybrids and more than 28,000 C-Max Hybrids sold domestically. The company also sold almost 7,500 Lincoln MKZ Hybrids. Ford's green-car totals for 2013 were up fivefold at the mid-year point, hinting that Ford's hybrid sales plateaued, at least temporarily, in recent months.