2005 Ford Mustang Base Coupe 2-door 4.0l on 2040-cars

Auto blog

Ford opens the doors on its Swedish rally skunkworks

It's always amazing to see how different kinds of racecars are made. Formula One racers are often constructed in modern architectural marvels that hint at some of the cutting-edge technology going into the racing. Conversely, rallying is all about sliding around on a varied course as fast as possible, but it often leaves a vehicle caked in mud. So it makes some sense Olsbergs MSE, or simply (OMSE) rally car shop in Nynashamn, Sweden, shows technological sophistication in a more down-to-earth setting. It builds Ford Fiesta ST racers for Global Rallycross there, and this new video gives viewers a tour through the work.
Former rally driver Andreas Eriksson runs OMSE. These days instead of racing, he and the company's 46 employees are building Ford racers from scratch. A ton of work goes into constructing each one, and according to Eriksson, it takes 400 hours to complete each body. At times, things are so busy that some of the technicians live in the shop in apartments that are on premises. There's even a restaurant to keep them fed. Sadly the dyno room is empty during this visit, though.
By the time OMSE is done, a rallycross car might resemble a Fiesta ST on the outside, but as you see in the video, it's a completely different beast underneath. Check out the work it takes to build one of them, and scroll down to read more about it in the official release.

NHTSA upgrades Ford floor mat unintended acceleration probe

According to a Bloomberg report, the National Highway Traffic Safety Administration has upgraded an investigation into complaints of unintended acceleration lodged against Ford vehicles. The investigation began in June of 2010 when just three complaints had been received and it only concerned the Ford Fusion and Mercury Milan, but this was at a time when the phrase "unintended acceleration" made grown men go pale. With 49 additional complaints received since then, the investigation has been reclassified as an engineering analysis - the last phase before a recall - and it has been expanded to include the Lincoln MKZ, making for a total of "around 480,000" units affected between the three sedans from the 2008 to 2010 model years.
The ostensible cause is that floor mats are trapping the accelerator pedal, but according to a Ford statement at the time, the entrapment is due to owners placing the optional all-weather floor mats, or aftermarket floor mats, on top of the car's standard floor mats. NHTSA has backed up that assessment, pinning the blame on "unsecured or double stacked floor mats."
On the face of it, it would appear that NHTSA has upgraded the status not because of Ford's error, but owner error, and Ford has stated publicly that it is "disappointed" in NHTSA's move. On top of NHTSA still being skittish after that other unintended acceleration debacle, it could be seen to be taking its time investigating all of the variables: it's reported that Ford changed its accelerator pedal design in 2010, a "heel blocker" in the floorpan has been considered a potential culprit in how the floor mats could be trapping the pedal, some drivers have said the floor mats weren't anywhere near the pedal, and according to a report in the LA Times, in "a letter sent by Ford to NHTSA in August 2010, the automaker said it found three injuries and one fatality that 'may have resulted from the alleged defect.'"

70% of pickups could use aluminum by 2025

In the next decade, the auto industry will see an explosion in its use of aluminum to cut weight and increase fuel economy, according to a study from market analysts Ducker Worldwide cited by The Detroit News. We are already seeing the lightweight metal show up extensively in luxury models from Europe, but with the impending launch of aluminum-intensive 2015 Ford F-150 (pictured above), North America is using it even more, as well. The report predicts 70 percent of US pickups to have aluminum bodies by 2025.
It won't just be pickups that see the benefit, though. The average amount of aluminum in US vehicles is forecasted by the study to grow from an average of 350 pounds in 2013 to about 550 pounds by 2025. The most common parts to use it will be hoods, doors and - to some extent - roofs, as well.
The massive increase in pickups' aluminum content hardly seems surprising. The F-150 is predicted to use so much that it might cause a short-term shortage, according to one earlier report. At the same time General Motors is heavily rumored to be negotiating with suppliers for the next generation Chevrolet Silverado and GMC Sierra. Ram is the last holdout of the Big Three, but the study predicts that not to last.