1999 Ford Mustang Base Coupe 2-door 3.8l on 2040-cars

Auto blog

Ford recalling 126,000 Fusions and Milans over wheel separation concern

Ford has announced a recall of certain Ford Fusion and Mercury Milan vehicles after an investigation by the National Highway Traffic Safety Administration. A total of 128,616 2010 and 2011 models equipped with steel wheels may have been manufactured with wheel studs that could crack and split over time. If that happens, the vehicle may experience a wheel separation.
According to The Detroit News, the company is aware of a total of 30 wheel separation incidents, one of which occurred on the front of the vehicle. Even so, no injuries have been reported as a result of the defect.
The problem apparently stems from the fact that the mounting pads on the vehicles' steel wheels may have been faulty from the factory. In addition, the wheel mounting face on rear disc brakes may not have been installed properly. Ford will inspect the rear disc face and replace them as necessary. In addition, the company will replace all of the vehicle's wheel studs free of charge. Head to the NHTSA website for more information, and click past the jump to view the full recall notice.

Ford recalls 9,900 vehicles across two campaigns

Ford is recalling a total of 9,885 vehicles in two campaigns. The Basics: In one recall, Ford will recall 9,017 examples of the 2013 Escape with build dates from January 11, 2012, to April 1, 2013, and the 2013-2014 Focus ST produced between May 3, 2012, and October 14, 2013. The Problem: Splices in the engine wiring harness might not have enough compression, and this can cause the manifold absolute pressure sensor to send incorrect signals to the powertrain control module. This issue could cause the engine to stall. Injuries/Deaths: None reported. The Fix: Dealers will replace the current crimped splices with new splices, according to the National Highway Traffic Safety Administration. If You Own One: The repair campaign will begin on January 4, 2016. More Information: Ford recalled the 2013 Escape and Focus ST in August 2014 for the same problem, and this is an expansion of that campaign, according to company spokesperson John Cangany to Autoblog. The Basics: In the smaller of the two campaigns, Ford will recall 868 examples of the 2013 Explorer, Explorer Police Utility, Taurus, Taurus Police Interceptor, Flex, Lincoln MKS, and MKT. The Problem: The fuel delivery module can crack, which would cause a fuel leak. Injuries/Deaths: None reported. The Fix: Dealers will replace the fuel delivery module. If You Own One: Owners should receive notice soon because NHTSA's report says the recall begins in December. More Information: According to Cangany, this recall is an expansion of a campaign from 2013 for these vehicles. RECALL Subject : Engine Wiring Splices may cause Stall Report Receipt Date: DEC 02, 2015 NHTSA Campaign Number: 15V813000 Component(s): ELECTRICAL SYSTEM Potential Number of Units Affected: 9,017 All Products Associated with this Recall Vehicle Make Model Model Year(s) FORD ESCAPE 2013 FORD FOCUS 2013-2014 Details Manufacturer: Ford Motor Company SUMMARY: Ford Motor Company (Ford) is recalling certain model year 2013 Escape vehicles manufactured January 11, 2012, to April 1, 2013, and 2013-2014 Focus ST vehicles manufactured May 03, 2012, to October 14, 2013. Insufficient compression in the engine wiring harness splices to the Manifold Absolute Pressure (MAP) sensor may provide incorrect signals to the powertrain control module (PCM). CONSEQUENCE: The incorrect signals could cause the vehicle to hesitate or the engine to stall, increasing the risk of a crash.

Check out Ford's fully automated self-parking car [w/video]

As automakers continue to find uses for autonomous and semi-autonomous vehicle technology, Ford of Europe has announced that it is developing a self-parking system for future use. More advanced than the Active Park Assist already offered in many Ford products, the new Fully Assisted Parking Aid can take full control of the vehicle and can navigate angled and perpendicular parking spots.
While today's Active Park Assist can only parallel park with the driver controlling the gas, brake and gear selection, Fully Assisted Parking Aid can operate steering, gas, brake and gear selection all while making sure the car is properly parked in the intended space. As with APA, the driver pushes a button to make the car look for a proper spot (at speeds of up to 18 miles per hour), and when an adequate space is located, the operator pushes another button (either inside the car or outside via remote control) for the car to park itself - the button must be pressed throughout the whole parking maneuver. Even though Ford says that the car can effect gear selections on its own, the system must still start from Neutral, and the automaker isn't saying whether the car can put itself into Park when done or put itself in Drive when the operator is ready to go.
Ford is also taking the opportunity to announce its new Obstacle Avoidance technology. This automated system is able to detect objects - including pedestrians - in the road, warn drivers of said objects and, if needed, stop and steer automatically to avoid hitting the obstacle. Both systems are still in the prototype phase, so there is no word as to when we could see either on a production vehicle.