Wild 24 Ford T-bucket 671 Blown Sbf Auto Chrome Jag Rear Turn-key on 2040-cars

Auto blog

NHTSA investigating 725k Ford, Mercury vehicles for stalling issue

Owners of Ford Escape, Mercury Mariner, Ford Fusion and Mercury Milan models, listen up. According to a report on Automotive News, the National Highway Traffic Safety Administration has opened an investigation into these four vehicles totaling an estimated 725,000 units. The investigation appears to center around a malfunctioning throttle body on non-hybrid models of the 2005-2012 Escape and 2011-2012 Fusion. With Mercury dying off after the 2011 model year, this probe will also apply to the 2005 through 2011 Mariner and the 2011 Milan. There has been some discussion around the Escape stalling issue for some time now, but this investigation appears to be larger in scope than before.
Though not a recall yet, NHTSA's Office of Defects Investigation (ODI) has received 123 complaints of stalling or surging vehicles, while Ford itself has logged 1,472 complaints. The investigation report, which is posted below, seems to indicate that a faulty circuit board for the throttle body could cause the vehicle to go into limp mode, which, according to NHTSA, could cause complaints of both stalling and surging.

First 1K next-gen Mustangs to carry 2014 1/2 model year?

A new report from Mustangs Daily, citing insider sources at Ford, tells us that the Blue Oval will produce 1,000 next-generation Mustangs with the model year designation of 2014 ½, to celebrate the 50th anniversary of the storied marque. The commemorative half-year designation is a rumor that's been swirling in Mustang forums for quite some time now, and seems more plausible than ever with this most recent report. Certainly it's not far-fetched to believe that Ford will want to make a big deal of the golden anniversary for its most-loved model.
The story (compiled by Drew Phillips, who runs the aforementioned Mustang site when he's not directing the photography on these pages) goes on to say that the limited-run cars will be the first built on the new Mustang platform internally known as S550 (and spied testing in the attached gallery). Each car is said to carry a "special" VIN and build number, though no performance upgrades versus the 2015 cars to follow are in the works. A collector's dream then, rather than a weekend racer's.

How the Ram Multifunction Tailgate compares to Ford, GMC, Honda

Ram just announced its Multifunction Tailgate — a descriptive if not very creative name. It's an asymmetrical barn-door arrangement, which can both fold down like a conventional tailgate or swing open like a gate. There's a new bed step, but unlike Ford or GM, the step isn't part of the tailgate itself. Rather, it kicks out from under the bumper (as opposed to out from under the driver's side of the rear bumper in its previous incarnation). So let's just focus on the tailgate functionality. A video of the Ram Multifunction Tailgate in action is above. For one, either of the swinging tailgate sections can be opened independently. They open to a full 88 degrees. In conventional flip-down mode, the tailgate works just like a normal one, too, with a 2,000-pound rating. The bottom line is that while it gives a variety of types of access to the load area, it doesn't "do" anything else. It's a $995 option on any Ram 1500. Its closest analogue is the Honda Ridgeline, which works basically the same way, but on that truck the tailgate swings as one piece. And the Honda's load rating isn't as hefty as the Ram's tailgate: 300 pounds. As Honda says, that's sufficient to hold the weight of the part of an ATV hanging out of the bed, or something similar, but it's a lighter-duty unit (and a lighter-duty truck) than the Ram's overall. Let's also get Ford's one-trick tailgate out of the way before comparing to the more analogous, and complicated, GM MultiPro. A bit of trivia: Ford's optional Tailgate Step is actually designed and supplied by Multimatic, better known as the outfit that builds the Ford GT and produces the DSSV spool-valve shocks. This step has been available for years. It pulls out of the top edge of the tailgate when the tailgate is lowered, deploying a single step. A separate handle pulls out from beside the step and flips up, giving a handhold. While it was initially (and infamously) mocked by competitors, with load floor heights as high as they are it's better than toting around a stepstool. It's currently a $375 standalone option. Now we get to the GMC MultiPro tailgate, the most complicated and multi-functioned around. It's essentially a tailgate within a tailgate, with a fold-out stopper that deploys from the inner tailgate. This gives it several functions depending on the position of all the parts. It can still be used like a normal tailgate, dropping down at the push of a button or using the key fob.