Auto Services in New Jersey

Williams Custom Tops-Interiors ★★★★★

Automobile Parts & Supplies, Automobile Seat Covers, Tops & Upholstery, Automobile Accessories

Address: 910 Woodbourne Rd, Fieldsboro

Phone: (215) 757-3100

Volkswagon of Langhorne ★★★★★

Auto Repair & Service, New Car Dealers, Used Car Dealers

Address: 1862 E Lincoln Hwy, Pennington

Phone: (215) 741-4100

Vip Honda Honda Automobiles ★★★★★

New Car Dealers

Address: 542 Somerset St, Fanwood

Phone: (908) 753-6071

Tri State Auto Glass ★★★★★

Automobile Parts & Supplies, Glass-Auto, Plate, Window, Etc, Windshield Repair

Address: 15511 Liberty Ave, West-New-York

Phone: (718) 206-0143

Solveri Collision Center ★★★★★

Auto Repair & Service, Automobile Body Repairing & Painting

Address: 2300 Route 88, Asbury-Park

Phone: (732) 202-7448

Scotts Auto Service ★★★★★

Auto Repair & Service

Address: 161 Kinderkamack Rd, Haworth

Phone: (201) 391-3433

Auto blog

Aluminum lightweighting does, in fact, save fuel

Mon, Apr 14 2014

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).

Ford, GM to collaborate on 9- and 10-speed transmissions

Mon, 15 Apr 2013

Back in October, there were reports that General Motors and Ford Motor Company were hard at work co-developing new nine- and ten-speed automatic transmissions, and now both automakers have confirmed this joint operation. While there are no specific vehicles mentioned to receive either transmission, a collaborative press release issued by GM and Ford mention that the transmission will be designed for front- and rear-wheel-drive cars, crossovers, trucks and SUVs.
These aren't the first powertrain components developed jointly between these cross-town rivals, either. The six-speed automatic currently used in vehicles like the Ford Edge, Ford Fusion, Chevrolet Cruze and Chevrolet Equinox was engineered in a similar fashion. As is the case with this existing transmission, both automakers will assist in the design, development and testing of the new transmissions, but each will build its own units in its own factories. Scroll down for the official press release.

Introducing the 1965 Ford Mustang

Sat, 24 Aug 2013

Put on your space suits and diving bell helmets, for it's time to step into a time capsule. The 50th anniversary of a historic model, like, say, the Porsche 911 this year, is certain to bring flights of nostalgia. This historical trip with the 1965 Mustang, though - preliminary hype for next year's anniversary, we know - is a swell museum exhibit for anyone who enjoys bygone days of the automobile.
Lee Iaccoca gave a speech to motoring journalists on April 1, 1964 at the New York World's Fair to introduce a sporty car for younger drivers. His opening line: "Good morning, ladies and gentlemen. Welcome to one of the proudest moments of our lives." The company was so excited by what it had made that the Mustang was Ford's first "International Press Introduction," being introduced to some 2,000 journos around the world on the same day in the US and 11 European cities. Even through its difficult points, no one at the time could have known how well the Mustang would acquit that pride.
After the intro, the press drove Mustangs 750 miles from New York to Dearborn, MI, reading press kits that touted features like the "vertical, three-sectional taillights/turn signals," "170" six-cylinder engine with 101 horsepower and the available Cruise-O-Matic transmission.

1930 Ford Model A Roadster Hot Rod on 2040-cars

Ford Model A for Sale