Find or Sell Used Cars, Trucks, and SUVs in USA

2013 Ford Fusion Se, 1.6l Gtdi, 2k Mi., Sync, Sat, 18in. Alloys, Cpo 7yr/100k on 2040-cars

US $21,994.00
Year:2013 Mileage:2302 Color: Gray /
 Black
Location:

Katy, Texas, United States

Katy, Texas, United States
Transmission:Automatic
Engine:1.6L GTDI
Body Type:Sedan
Vehicle Title:Clear
Fuel Type:Gasoline
For Sale By:Dealer
VIN: 3FA6P0HR5DR107730 Year: 2013
Interior Color: Black
Make: Ford
Number of Cylinders: 4
Model: Fusion
Drive Type: FWD
Warranty: Yes
Mileage: 2,302
Sub Model: SE 1.6L GTDI, AUTO, FORD CPO CERTIFIED
Exterior Color: Gray
Condition: Certified pre-owned: To qualify for certified pre-owned status, vehicles must meet strict age, mileage, and inspection requirements established by their manufacturers. Certified pre-owned cars are often sold with warranty, financing and roadside assistance options similar to their new counterparts. See the seller's listing for full details. ... 

Auto Services in Texas

Zoil Lube ★★★★★

Auto Repair & Service
Address: 3321 Fondren Rd, Fresno
Phone: (713) 783-2050

Young Chevrolet ★★★★★

New Car Dealers, Used Car Dealers
Address: 9301 E R L Thornton Fwy, Seagoville
Phone: (214) 328-9111

Yhs Automotive Service Center ★★★★★

Auto Repair & Service
Address: 19831 Greenwind Chase Dr, Katy
Phone: (281) 944-9748

Woodlake Motors ★★★★★

Used Car Dealers
Address: 2416 N Frazier St, Dobbin
Phone: (936) 441-3500

Winwood Motor Co ★★★★★

Auto Repair & Service, Gas Stations, Towing
Address: 4922 Graves Rd, Santa-Fe
Phone: (409) 925-2039

Wayne`s Car Care Inc ★★★★★

Auto Repair & Service, Automobile Parts & Supplies, Automobile Accessories
Address: 2725 S Cooper St, Richland-Hills
Phone: (817) 795-8436

Auto blog

1964 Ford GT40 prototype sells for $7M

Mon, 14 Apr 2014

Seven-figure Ferraris are not horribly rare. Heck, an eight-figure Ferrari isn't a rare occurrence. Between modern masterpieces like the Enzo and more classic offerings, cracking the million-dollar mark isn't a particularly tall order for the cars from Maranello. For a Ford, though, it's a big deal.
Now, this is not just some rare Mustang. This is a GT40, the car that Henry Ford II commissioned to whip Enzo Ferrari around a track in France. As far as the Le Mans-winning racers go, they don't get much rarer than this one. Sold at the Mecum Auctions in Houston, this is one of the prototypes, meaning it's one of the very first GT40s ever built. That makes its $7 million winning a bid, a record for on-air coverage of the auction, a pretty darn impressive figure.
You can watch the auction below, but first, take a look back at our original story on this rare Blue Oval.

2016 Ford Focus RS may yet be AWD, US sales likely

Fri, 29 Aug 2014

When it comes to forbidden fruit, few vehicles are spoken of in as hushed a tone as the Ford Focus RS. The turbocharged, five-cylinder hot hatch could only be seen from afar by American customers as it tore up the roads of Europe. And while it's safe to say that Ford's Yankee fans are quite happy to now be on equal footing with drivers in the old country thanks to the Focus ST, we doubt there'd be much protestation over a successor to the RS arriving stateside.
Of course, we've seen images of the new RS undergoing testing, but a new story by Road and Track aims to fill in some very large blanks in our knowledge of that car, thanks to a pair of mysterious insiders at the Ford. Chief among those is this - the RS will almost certainly make its way to the US, albeit in limited quantities. It gets better, though.
Under hood, the new RS is unsurprisingly expected to borrow the 2.3-liter, turbocharged four-cylinder from the 2015 Ford Mustang and 2015 Lincoln MKC. While that twin-scroll turbo produces 310 horsepower in the Mustang and 285 ponies in the MKC, R&T expects the RS to deliver quite a bit more firepower - 325 to 350 hp, with preference going to the higher output due to the limited-edition nature of the RS. This roughly fits with previous reports.

Ford 3D-printing Mustang out of chocolate and candy for Valentine's Day

Thu, 13 Feb 2014

Is your beloved in love with the new 2015 Ford Mustang? Do they like chocolate (that's a trick question - everyone likes chocolate)? Are they a bit of a futurist? Then this Hallmark holiday, you need to get them this Ford Mustang, 3D-printed in sweet, delicious chocolate.
Ford is teaming with 3D Systems' Sugar Lab in LA to produce the super-accurate pony car confections in both chocolate and sugar candy varieties. The process kicked off with a CAD rendering of the 2015 Mustang, which was then programmed into the 3D printer. After a bit of work from the machine, a four-inch long, two-inch tall Mustang was the result. Why the tieup with 3D Systems, though?
"We wanted to create something fun to show that while 3D printing made these edible Mustangs, manufacturing-level 3D printing was used in the development of Ford's all-new sports car," said Paul Susalla, Ford's supervisor of 3D printing.