2012 Ford Focus Se Sedan 4-door 2.0l on 2040-cars

Auto blog

Recharge Wrap-up: Ford 1.0L EcoBoost a hit in Europe; Build a tiny inverter, win $1 million

In Europe, Ford's 1.0-liter EcoBoost engine is the best-selling turbocharged gasoline engine. The three-cylinder motor powers 20 percent of new Fords sold in Europe. Earlier this year, it won its third International Engine of the Year award, and between January and June, it was sold in about 120,000 cars. So far this year, 38 percent of Fords sold in the Netherlands, 35 percent in Denmark and 32 percent in Switzerland have been powered by the 1.0-liter EcoBoost. The engine's turbocharger spins at 248,000 rpm, and provides 24 psi of pressure. The engine produces up to 138 horsepower, depending on the version. Read more in the press release below. When lithium-ion battery packs are retired from the road, remanufacturing, repurposing, and recycling are worthwhile options, according to a study by Mineta Transportation Institute. The study included a cost-benefit analysis of those three options, and found remanufacturing to be the best route. To get the most out of them, batteries should be tested and have their damaged cells replaced then put back to use. Repurposing is the second best option, using the remaining available charge for something besides cars. Recycling on its own isn't profitable, but it could make economic sense with "increased technological breakthroughs." Learn more at Recycling International or download the report here. A smaller inverter for EVs can win you $1 million. The Little Box Challenge is an open competition to build a power inverter with a density of at least 50 watts per cubic inch. Google and the Institute of Electrical and Electronics Engineers (IEEE) are offering the hefty prize to the team that builds the inverter with the highest power density within an enclosed volume of 40 cubic inches. Teams must register by September 30. Read more at Green Car Congress or learn more at the Little Box Challenge website.

NHTSA investigating 725k Ford, Mercury vehicles for stalling issue

Owners of Ford Escape, Mercury Mariner, Ford Fusion and Mercury Milan models, listen up. According to a report on Automotive News, the National Highway Traffic Safety Administration has opened an investigation into these four vehicles totaling an estimated 725,000 units. The investigation appears to center around a malfunctioning throttle body on non-hybrid models of the 2005-2012 Escape and 2011-2012 Fusion. With Mercury dying off after the 2011 model year, this probe will also apply to the 2005 through 2011 Mariner and the 2011 Milan. There has been some discussion around the Escape stalling issue for some time now, but this investigation appears to be larger in scope than before.
Though not a recall yet, NHTSA's Office of Defects Investigation (ODI) has received 123 complaints of stalling or surging vehicles, while Ford itself has logged 1,472 complaints. The investigation report, which is posted below, seems to indicate that a faulty circuit board for the throttle body could cause the vehicle to go into limp mode, which, according to NHTSA, could cause complaints of both stalling and surging.

Ford cleans up painting process with cameras

Knowing how the bacon gets made rarely entices us and, in the same vein, the same usually goes for knowing about how new cars get painted. But in both instances, however, quality - or a lack thereof - is instantly obvious. In terms of the latter, Ford is showing off its new paint quality process with 3D Dirt Detection Technology to find imperfections in vehicle paint more easily and more quickly.
This process - being performed on the F-150 SVT Raptor above - uses 16 computer-controlled cameras to create a three-dimensional model (inset) of the vehicle to detect flaws in the paint including dirt particles, which can then be buffed out manually. Ford says this new technology cuts down on time spent looking for paint flaws and gives workers more time to correct those that are discovered.
Currently, Ford only uses its 3D Dirt Detection Technology system at three factories (the Dearborn, MI facility, along with those in Louisville, Kentucky and Valencia, Spain), but it will soon spread to five more plants in North America. Ford has released a video and press release for this innovative and unexpectedly interesting process, both of which are posted below.