11focus Se, 2.0l 4 Cylinder, Auto, Cloth, Pwr Equip, Cruise,alloys,clean 1 Owner on 2040-cars

Auto blog

Toyota fears supplier pressure in Australia with GM pull out

With Ford and General Motors both announcing an end to production in Australia, the country's auto industry is in a bad way. With the exit of two big players, there's increased concern that a third Australian manufacturer, Toyota, will be forced out, as well.
"We are saddened to learn of GM Holden's decision. This will place unprecedented pressure on the local supplier network and our ability to build cars in Australia," Toyota Australia said in a statement. The GM closure of Holden production will be the direct end to 2,900 jobs, but will also force a dramatic reduction in the size of the country's supplier network, as there will simply be fewer cars to build.
In the same statement, Toyota Australia said it would work with suppliers and local government to figure out whether continuing production Down Under was even feasible. According to Automotive News, a representative for the Australian Manufacturing Workers' Union told reporters it was "highly likely" that Toyota would also close up shop within the next few years.

Mustang Cobra Jet prototype garners $200k for charity at Barrett-Jackson

A few weeks ago we brought you news of a one-off Mustang Cobra Jet that Ford was donating to charity. The car was set to be auctioned off by Barrett-Jackson in Las Vegas to benefit the National Multiple Sclerosis Society. Now that auction has taken place, bringing in an impressive $200,000 for MS research.
That's a lot of zeros for a Mustang, much less one you can't even drive on the street. But the unique pony car, bearing serial number 2014 BJMS CJXX1, packs a 5.0-liter supercharged V8, competition gearbox, wheelie bar, roll cage... all you could want, in short, in a turn-key drag racer. And all that for a good cause.

Ford recalls 9,900 vehicles across two campaigns

Ford is recalling a total of 9,885 vehicles in two campaigns. The Basics: In one recall, Ford will recall 9,017 examples of the 2013 Escape with build dates from January 11, 2012, to April 1, 2013, and the 2013-2014 Focus ST produced between May 3, 2012, and October 14, 2013. The Problem: Splices in the engine wiring harness might not have enough compression, and this can cause the manifold absolute pressure sensor to send incorrect signals to the powertrain control module. This issue could cause the engine to stall. Injuries/Deaths: None reported. The Fix: Dealers will replace the current crimped splices with new splices, according to the National Highway Traffic Safety Administration. If You Own One: The repair campaign will begin on January 4, 2016. More Information: Ford recalled the 2013 Escape and Focus ST in August 2014 for the same problem, and this is an expansion of that campaign, according to company spokesperson John Cangany to Autoblog. The Basics: In the smaller of the two campaigns, Ford will recall 868 examples of the 2013 Explorer, Explorer Police Utility, Taurus, Taurus Police Interceptor, Flex, Lincoln MKS, and MKT. The Problem: The fuel delivery module can crack, which would cause a fuel leak. Injuries/Deaths: None reported. The Fix: Dealers will replace the fuel delivery module. If You Own One: Owners should receive notice soon because NHTSA's report says the recall begins in December. More Information: According to Cangany, this recall is an expansion of a campaign from 2013 for these vehicles. RECALL Subject : Engine Wiring Splices may cause Stall Report Receipt Date: DEC 02, 2015 NHTSA Campaign Number: 15V813000 Component(s): ELECTRICAL SYSTEM Potential Number of Units Affected: 9,017 All Products Associated with this Recall Vehicle Make Model Model Year(s) FORD ESCAPE 2013 FORD FOCUS 2013-2014 Details Manufacturer: Ford Motor Company SUMMARY: Ford Motor Company (Ford) is recalling certain model year 2013 Escape vehicles manufactured January 11, 2012, to April 1, 2013, and 2013-2014 Focus ST vehicles manufactured May 03, 2012, to October 14, 2013. Insufficient compression in the engine wiring harness splices to the Manifold Absolute Pressure (MAP) sensor may provide incorrect signals to the powertrain control module (PCM). CONSEQUENCE: The incorrect signals could cause the vehicle to hesitate or the engine to stall, increasing the risk of a crash.