2009 Ford Flex Sel Awd- Clean Carfax! on 2040-cars

Auto blog

AMC Trans Am Javelin SST, an ultra-rare underdog, is up for auction

Among the rarest of the American muscle cars that went racing in the early Seventies — cars including the Camaro Z/28 and the Boss 302 Mustang — the 1970 AMC Trans Am Javelin SST may be the most hard to find, and among the most valuable. Only 100 units of this unique Javelin were produced, and one of them is up for auction at the Mecum event in Dallas on September 20. The Trans Am Javelin was fashioned in a patriotic livery of tricolor paint — red, white and blue — and arrived after the American Motors Corporation had decided in 1968 to compete in the Trans Am racing series against Ford and General Motors. The company's chief driver, Mark Donohue, would dominate the 1971 season, taking seven wins in his Javelin AMX and that yearÂ’s SCCA Trans-Am Championship. AMC took the trophy with 82 points, well ahead of Ford's 61, Chevrolet's 17 and Pontiac's paltry 7. The example listed for auction came equipped with a 390-cubic-inch V-8 engine with 325 horsepower at 5,000 rpm and 420 pound-feet of torque, power steering and brakes, dual exhaust, BorgWarner four-speed manual transmission and Hurst competition shifter. Its “ram induction system” sealed a chamber around the air filter so that cool air from the functional hood scoop would be funneled into the intake. This JavÂ’s factory price was $3,995 — a mere $32,000 or so in today's money, though it was expensive by the standards of the time. The 100 Trans Ams were among 19,714 Javelin units built in 1970, so they started out rare, and today the surviving examples are highly collectible, if and when they come up for sale. No bid estimate is available yet. Related Video: Motorsports Chevrolet Ford Pontiac Auctions Automotive History Racing Vehicles Classics

2020 Ford Explorer, Lincoln Aviator reportedly facing numerous QC issues

A lengthy report in the Detroit Free Press delves into a range of quality control issues confronting the 2020 Ford Explorer and its luxury platform sibling, the 2020 Lincoln Aviator. Freep says it's been following the issue for two months, tapping various unnamed sources for information on the automaker's unorthodox route to resolution. Seems the problem is Explorers and Aviators leaving the production line at the Chicago Assembly Plant with flaws in areas like the chassis, transmission and suspension, said vehicles trucked to Ford's Flat Rock Assembly Plant (FRAP) outside of Detroit for repair. The estimates range from 10,000 to 18,000 vehicles affected, numbers so high that Ford has sought help from Roush Engineering in nearby Allen Park, and brought workers and managers from other plants in the Midwest to FRAP to get vehicles repaired and shipped to dealers. Ford hasn't shared the nature of the problems with anyone outside the company, including dealers and customers. Freep's sources are said to include workers who have provided photos of certain vehicles and of tents used to house parts at the FRAP repair site. The Explorer chassis allegedly has an unidentified problem that engineers are using X-rays to diagnose, and the transmission is having problems sensing when it's in park or going into park. Both the Explorer and Aviator have come off the line with HVAC units that only blow hot air. And the Aviator's height-adjustable suspension enters failure mode for unknown reasons. These come on top of quotidian mishaps common to every new vehicle, but that are meant to be sorted in pre-production, like missing emblems and trim pieces. They also come on top of a recall in early August issued for the Explorer and Aviator concerning the instrument cluster and parking brake, and another at the end of August over rear seatbacks that could collapse in a crash. An automaker spokesperson told Freep, "Making updates to preproduction models based on all-new platforms as they roll off the assembly line – is standard industry practice." Except these aren't pre-production, these are early production vehicles that paying customers and dealers are waiting for, and some of the affected vehicles have been pulled off dealer lots. Dealers say they are fine waiting for the trucks to get sorted out, and they'd rather have Ford fix the problems before the SUVs go to customers.

Ford taps Canada-based Multimatic to build carbon fiber Ford GT

Ford has given Canadian firm Multimatic the nod to build the carbon fiber body on the new GT – The Blue Oval says it has worked with this company for 30 years. The global supplier provides parts and engineering to various automakers, and while based in Markham, Ontario it has 12 plants in Canada, the US, Mexico, England, and China. When announcing the decision at the Canadian International Auto Show, Ford says it chose them "because they have specialized equipment for carbon fiber production and expertise in carbon fiber assembly," and we've heard that the 600-horsepower coupe will be produced in a purpose-built facility at Ford's factory in Markham. Even better than that – for GT purposes and for possible hints at a Le Mans run – the Multimatic Motorsports division can be contracted for engineering and race team management. They currently produce the Boss 302R racecar in the Continental Tire SportsCar Challenge, worked on the FR500C, and their Multimatic Motorsports Lola B2K/40 won its class at the 24 Hours of Le Mans in 2000. The first models will roll off the line at the end of next year. Production numbers are rumored to be in the low hundreds, with a six-figure price tag around $200,000. They'll go into production in time for some sort of 50th anniversary celebration of the GT40 taking the the top three spots at Le Mans in 1966. Related Video: Featured Gallery 2017 Ford GT: Chicago 2015 View 30 Photos News Source: CBCImage Credit: Live images copyright 2015 Drew Phillips / AOL Plants/Manufacturing Ford Coupe Luxury Performance Multimatic