2011 Ford Fiesta Ses on 2040-cars

Auto blog

2014 Ford Transit unveiled in Chassis Cab and Cutaway versions

As a leader in commercial vehicles here in the US, we knew Ford wouldn't take too long to show off the chassis cab and cutaway versions of its 2014 Ford Transit van. Set to go on sale this fall, Ford already revealed the full-body version of the Transit, and now it has pulled the cover off exposed-frame models just in time to to compete against the all-new Ram Promaster.
The term "chassis cab" refers to models with a fully enclosed cabin used for box vans or rental trucks, while cutaway models leave the cabin open behind the B-pillars for a pass-through on vehicles such as Class C motorhomes or ambulances. Both will offer three wheelbase options (138, 156 and 178 inches), the choice of single or dually rear axles, and plenty of upfitter-friendly touches including a pre-wired body harness and multiple body mount locations.
The new design will also help make upfitting a little easier since the fuel filler is now built into the cab (just behind the driver's door). Those integrated fuel filler necks will serve to feed either a 3.7-liter V6, a 3.5-liter EcoBoost V6, or a 3.2-liter Power Stroke diesel. Transit chassis cab and cutaways will wear varying Gross vehicle weight ratings from 9,000 pounds to 10,360 pounds depending on spec.

Recharge Wrap-up: Ford's "snowtonomous" Fusion Hybrid, Porsche eyes battery makers

Bosch and Panasonic are vying to be the battery supplier for Porsche's electric sports car based on the Mission E concept. While Bosch's costs may be higher, its solution would offer simpler logistics. Panasonic is already well established as a battery maker, providing the packs for the Porsche car's rival, Tesla. "We're in the final stage of making a decision," says Porsche CEO Oliver Blume, declining to comment on specific manufacturers. Neither Bosch nor Panasonic provided comment. Read more from Automotive News. Renault will supply a fleet of 150 Renault Zoe EVs for a smart solar charging project in Utrecht, Netherlands. The project involves the installation of 1,000 EV chargers powered by 10,000 photovoltaic panels. The Renault Zoes would be used as part of a carsharing program powered by the solar chargers. Renault and its partners will also implement a vehicle-to-grid system to provide energy during peak demand from the solar chargers and connected EVs. Read more in the press release from Renault. Ford has been testing an autonomous Fusion Hybrid prototype that is capable of driving itself in snowy conditions. Ford uses 3D mapping to scan the drive route. Its LiDAR laser mapping can even detect single falling snowflakes. It collects and processes up to 600 gigabytes of data per hour, comparing its environment to saved maps, a process that helps establish location more precisely than GPS. In addition to the LiDAR systems, the car is also equipped with cameras and radar to help it navigate. Eventually, the car could even be able to clean off its sensors when it detects loss of performance from ice and dirt. Read more in the press release below. FROM AUTONOMY TO SNOWTONOMY: HOW FORD FUSION HYBRID AUTONOMOUS RESEARCH VEHICLE CAN NAVIGATE IN WINTER DEARBORN, Mich., March 10, 2016 – Driving in snow can be a slippery challenge, with the potential for one blizzardy gust to white-out your field of view – a situation faced by the majority of people in the United States. So if self-driving cars are to become a reality – and they almost certainly will – they must be able to navigate snow-covered roads. In its quest to bring self-driving vehicles to millions of people around the world, Ford reveals six facts about its technology that allows for a car to drive itself in snow. 1. Mapping the way: Ford first creates high-resolution 3D maps using LiDAR technology to scan the area its autonomous vehicle will later drive in the snow.

Ford abandons MyFord Touch, all hail Sync 3 infotainment [w/video]

MyFord Touch has been among the most widely disdained automotive infotainment systems on the market, practically since its introduction in 2010. Consumer Reports was among the most vocal critics, all but advocating its lynching by an angry mob armed with torches and pitchforks. Not surprisingly, then, after such a critical walloping, Ford has finally decided to say goodbye to the unloved tech, declaring the end of MyFord Touch branding in favor of Sync 3 for its upcoming, all-new system. Ford is promising everything you would expect from Sync 3, including faster response time, better voice-command integration, easier controls and a more useable interface. The screen layout includes fewer items to make them easier to discern, and the icons are made from large, high-contrast buttons. There's also a dedicated tab for apps at the bottom of the screen in addition to those for audio, climate, phone and navigation. Another useful feature is the fact that Sync 3 can download improvements over your home Wi-Fi for easier updates. In addition to the revamped interface, the software running behind the scenes is a big change too. Rather than MyFord Touch's Microsoft-sourced system, Sync 3 uses the Blackberry-owned QNX, according to Automotive News. Such a switch was rumored earlier this year. Drivers still have to live with MyFord Touch a little longer, though. According to Automotive News, Ford said that the change to Sync 3 will happen during the 2016 model year with complete integration into the lineup by the end of the 2016 calendar year. It will come standard on Titanium trim models and as a separate option will be priced in line with the current MyFord Touch. The Sync 3 brand will carry over to Lincoln, too, but with a different look. The gallery above shows a few more looks at the interface, and we invite you to scroll down to watch a video of Sync 3 in action and to read Ford's press release about it, below. This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings.