Super Clean 2011 Ford F350 Crewcab Diesel Dually 4x4 King Ranch Package,nav. on 2040-cars

Auto blog

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).

Ford recalling 126,000 Fusions and Milans over wheel separation concern

Ford has announced a recall of certain Ford Fusion and Mercury Milan vehicles after an investigation by the National Highway Traffic Safety Administration. A total of 128,616 2010 and 2011 models equipped with steel wheels may have been manufactured with wheel studs that could crack and split over time. If that happens, the vehicle may experience a wheel separation.
According to The Detroit News, the company is aware of a total of 30 wheel separation incidents, one of which occurred on the front of the vehicle. Even so, no injuries have been reported as a result of the defect.
The problem apparently stems from the fact that the mounting pads on the vehicles' steel wheels may have been faulty from the factory. In addition, the wheel mounting face on rear disc brakes may not have been installed properly. Ford will inspect the rear disc face and replace them as necessary. In addition, the company will replace all of the vehicle's wheel studs free of charge. Head to the NHTSA website for more information, and click past the jump to view the full recall notice.

Ford Fiesta ST customs get wild at SEMA

The massive 57-car SEMA showcase by Ford ranges from obvious aftermarket-friendly models like the Mustang, to the not so obvious ones, like the Transit Connect and cute-as-an-explosive-button Fiesta ST. Ford plucked several Fiesta STs for SEMA duty, and we were on the show floor today to get a closer look at some of them.
First up is the striking COBB Tuning and Tanner Foust Racing Fiesta ST (above) finished in a black-and-gray digital camouflage, much like that used in the military, and is meant to raise awareness for the Pat Tillman Foundation. COBB also fitted a three-inch exhaust and a cold-air intake. A new shift knob, carbon-fiber hood and a Kicker stereo round out the mix of upgrades.
MRT got its hands on a Fiesta ST and created a car inspired by Forza Motorsport 5 (below, left). Featuring a two-tone paint job and more performance upgrades than you can shake a stick at, this Fiesta ST is one of the cooler compacts at Ford's stand. A high-performance exhaust system, along with a complimentary COBB induction system, allows the ST to breathe better, while an H&R coil over suspension and Steeda brakes help it stop and turn better than stock.