Red Crew Cab 6.0 Power Stroke Diesel Low Miles Extras New Tires Financing Clean on 2040-cars

Auto blog

Jay Leno's Garage goes eco with Ricardo HyBoost

"Now before you turn away, this is not another boring hybrid car thing..." Despite the slightly defensive introduction from Jay, the latest episode of Jay Leno's Garage is actually pretty fascinating. The Ricardo HyBoost is a 2009 Ford Focus that has had a 1.1-liter engine swapped in for the stock 2.0-liter four. That might not get you performance enthusiasts out there fired up, until, that is, you hear that the 1.1L is also fed by both a turbocharger and an electrically driven supercharger for an instant-on "torque-fill" effect. Sounds about right, considering that Ricardo engineering is part of the genius behind the McLaren P1.
Perhaps most exciting of all, the Ricardo folks say that the package should run somewhere in the neighborhood of $1,100. A sort of performance-hybrid that makes sense for the frugal driver and the enthusiast one, then. There's a lot more to the HyBoost, all of which can be seen in the video below.

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).

Ford investing $500M in engine plant for 2.7L EcoBoost production

Ohio is a hot area for Ford at the moment with the announcement just a few weeks ago that production of the next-generation F-650/F-750 medium-duty trucks would move from Mexico to the Ohio Assembly Plant in Avon Lake, Ohio. Now, Ford is investing $500 million to hire 300 workers at its Lima Engine Plant in Lima, Ohio, to add production of the twin-turbo 2.7-liter EcoBoost V6 for the 2015 F-150.
The latest investment will be used to add a new flexible engine assembly system and renovate 700,000 square feet of the plant for machining and assembly areas. The Lima factory already builds Ford's 3.5-liter and 3.7-liter Duratec V6 engines. The plant opened in 1957, and it's on track to build its 40 millionth engine later this year.
Ford claims that the 2.7-liter EcoBoost will offer V8 performance with better efficiency in the F-150. It comes standard with intelligent stop/start that doesn't activate when the truck is towing or in four-wheel drive, and it's made from a combination of compacted graphite iron and aluminum for low weight and high strength. The company says that V6 engines have already proven popular in the F-150 with 57 percent of trucks in 2014 being equipped with either the naturally aspirated 3.7-liter or turbocharged 3.5-liter EcoBoost engines.