2008 Ford F-350 Xlt on 2040-cars

Auto blog

Ford opens the doors on its Swedish rally skunkworks

It's always amazing to see how different kinds of racecars are made. Formula One racers are often constructed in modern architectural marvels that hint at some of the cutting-edge technology going into the racing. Conversely, rallying is all about sliding around on a varied course as fast as possible, but it often leaves a vehicle caked in mud. So it makes some sense Olsbergs MSE, or simply (OMSE) rally car shop in Nynashamn, Sweden, shows technological sophistication in a more down-to-earth setting. It builds Ford Fiesta ST racers for Global Rallycross there, and this new video gives viewers a tour through the work.
Former rally driver Andreas Eriksson runs OMSE. These days instead of racing, he and the company's 46 employees are building Ford racers from scratch. A ton of work goes into constructing each one, and according to Eriksson, it takes 400 hours to complete each body. At times, things are so busy that some of the technicians live in the shop in apartments that are on premises. There's even a restaurant to keep them fed. Sadly the dyno room is empty during this visit, though.
By the time OMSE is done, a rallycross car might resemble a Fiesta ST on the outside, but as you see in the video, it's a completely different beast underneath. Check out the work it takes to build one of them, and scroll down to read more about it in the official release.

Ford recalls 9,900 vehicles across two campaigns

Ford is recalling a total of 9,885 vehicles in two campaigns. The Basics: In one recall, Ford will recall 9,017 examples of the 2013 Escape with build dates from January 11, 2012, to April 1, 2013, and the 2013-2014 Focus ST produced between May 3, 2012, and October 14, 2013. The Problem: Splices in the engine wiring harness might not have enough compression, and this can cause the manifold absolute pressure sensor to send incorrect signals to the powertrain control module. This issue could cause the engine to stall. Injuries/Deaths: None reported. The Fix: Dealers will replace the current crimped splices with new splices, according to the National Highway Traffic Safety Administration. If You Own One: The repair campaign will begin on January 4, 2016. More Information: Ford recalled the 2013 Escape and Focus ST in August 2014 for the same problem, and this is an expansion of that campaign, according to company spokesperson John Cangany to Autoblog. The Basics: In the smaller of the two campaigns, Ford will recall 868 examples of the 2013 Explorer, Explorer Police Utility, Taurus, Taurus Police Interceptor, Flex, Lincoln MKS, and MKT. The Problem: The fuel delivery module can crack, which would cause a fuel leak. Injuries/Deaths: None reported. The Fix: Dealers will replace the fuel delivery module. If You Own One: Owners should receive notice soon because NHTSA's report says the recall begins in December. More Information: According to Cangany, this recall is an expansion of a campaign from 2013 for these vehicles. RECALL Subject : Engine Wiring Splices may cause Stall Report Receipt Date: DEC 02, 2015 NHTSA Campaign Number: 15V813000 Component(s): ELECTRICAL SYSTEM Potential Number of Units Affected: 9,017 All Products Associated with this Recall Vehicle Make Model Model Year(s) FORD ESCAPE 2013 FORD FOCUS 2013-2014 Details Manufacturer: Ford Motor Company SUMMARY: Ford Motor Company (Ford) is recalling certain model year 2013 Escape vehicles manufactured January 11, 2012, to April 1, 2013, and 2013-2014 Focus ST vehicles manufactured May 03, 2012, to October 14, 2013. Insufficient compression in the engine wiring harness splices to the Manifold Absolute Pressure (MAP) sensor may provide incorrect signals to the powertrain control module (PCM). CONSEQUENCE: The incorrect signals could cause the vehicle to hesitate or the engine to stall, increasing the risk of a crash.

Ford dealers offered discounts on tools to fix aluminum

With the introduction of the aluminum-bodied 2015 Ford F-150 (and the likely use of aluminum in future Ford products), Ford is looking to help its dealerships reduce costs related to repairing this more labor-intensive material. Automotive News is reporting that Ford dealers with body shops will require an estimated $30,000 to $50,000 in equipment and training to work on aluminum, and to help alleviate the financial burden of the new F-150, Ford has announced a special 20-percent discount on this equipment.
Dealers will be able to save up to $10,000 on tools such as welders, air-filtration systems and rivet guns and to create aluminum-specific work stations. The new F-150 goes on sale in the fourth quarter, and dealers have until October 31 to take advantage of this deal, according to the report.