1995 Ford F350 Aluminum Flatbed Dump Truck on 2040-cars

Auto blog

Ford recalls 600,000 older-model sedans for braking issue

Ford is recalling 600,166 older-model Ford, Lincoln and Mercury vehicles over an issue that could affect braking and increase the risk of a crash. The safety recall covers certain Ford Fusion, Mercury Milan and Lincoln MKZ sedans from the 2006 through 2010 model years that were built at Ford’s Hermosillo Assembly Plant in Mexico between Feb. 22, 2006, and July 15, 2009. Ford says a valve that is normally closed inside the hydraulic control unit may get stuck in the open position or be slow to close, which could make it harder to engage the brakes and increase risk of a crash. Ford says itÂ’s aware of 15 reports of accidents and two injuries possibly related to the issue. Dealers will inspect the hydraulic control unit for signs of the problem and replace it, if necessary. The dealers will pressure-flush the system with brake fluid and replace the reservoir cap with a new one. Ford is also issuing a small recall of 33 of its 2020 F-150 trucks in the U.S. and 51 in Canada over potentially damaged spare tires. It says the bead area on the tires may have been damaged when it was mounted onto the wheel assembly, leaving it vulnerable to corrosion, separation of the bead wire and ultimately a rapid loss of air pressure and detachment from the wheel. Dealers will replace the spare tire. Affected vehicles were built at the Dearborn Truck Plant from Nov. 10-21 of this year.

Rising aluminum costs cut into Ford's profit

When Ford reports fourth-quarter results on Wednesday afternoon, it is expected to fret that rising metals costs have cut into profits, even as rivals say they have the problem under control. Aluminum prices have risen 20 percent in the last year and nearly 11 percent since Dec. 11. Steel prices have risen just over 9 percent in the last year. Ford uses more aluminum in its vehicles than its rivals. Aluminum is lighter but far more expensive than steel, closing at $2,229 per tonne on Tuesday. U.S. steel futures closed at $677 per ton (0.91 metric tonnes). Republican U.S. President Donald Trump's administration is weighing whether to impose tariffs on imported steel and aluminum, which could push prices even higher. Ford gave a disappointing earnings estimate for 2017 and 2018 last week, saying the higher costs for steel, aluminum and other metals, as well as currency volatility, could cost the company $1.6 billion in 2018. Ford shares took a dive after the announcement. Ford Chief Financial Officer Bob Shanks told analysts at a conference in Detroit last week that while the company benefited from low commodity prices in 2016, rising steel prices were now the main cause of higher costs, followed by aluminum. Shanks said the automaker at times relies on foreign currencies as a "natural hedge" for some commodities but those are now going in the opposite direction, so they are not working. A Ford spokesman added that the automaker also uses a mix of contracts, hedges and indexed buying. Industry analysts point to the spike in aluminum versus steel prices as a plausible reason for Ford's problems, especially since it uses far more of the expensive metal than other major automakers. "When you look at Ford in the context of the other automakers, aluminum drives a lot of their volume and I think that is the cause" of their rising costs, said Jeff Schuster, senior vice president of forecasting at auto consultancy LMC Automotive. Other major automakers say rising commodity costs are not much of a problem. At last week's Detroit auto show, Fiat Chrysler Automobiles NV's Chief Executive Officer Sergio Marchionne reiterated its earnings guidance for 2018 and held forth on a number of topics, but did not mention metals prices. General Motors Co gave a well-received profit outlook last week and did not mention the subject. "We view changes in raw material costs as something that is manageable," a GM spokesman said in an email.

This is what a 3D-printed liquid metal Ford Torino looks like

Artist Ioan Florea has encapsulated a 1971 Ford Torino with 3-D-printed liquid metal transferred onto the car using technology that he developed, and the result is a stunningly shiny, seamless design.
"The surface has the highest coefficient of reflectivity never achieved before," Florea told us in an e-mail, using "nano-materials and nano-pigments that create an internal three-dimensional structure and dictate the polymer how to behave." Sure... We'll leave it to him to make any more 3-D-printed liquid metal-transferred art pieces.
Florea grew up in Romania, and the motivation behind picking the old Ford as his canvas came from his childhood memories of what an American car is - "big and wide and fascinating," he says - and the European name of the car itself, which it shares with an Italian city.