1989 F350 ** Solid Truck ** 2nd Owner - 4 Door on 2040-cars

Auto blog

Watch these videos of an NHRA racer's bodywork blowing off into a crowd

Just a few months ago, fan safety at racetracks was a hot topic following the last-lap NASCAR Nationwide Series crash at Daytona that sent large pieces of racecars into the grandstands injuring 33 fans. Now, a freak incident at a National Hot Rod Association event resulted in a drag racer's bodywork flying into the crowd at the NHRA Four-Wide Nationals in Charlotte over the weekend. The carbon-fiber body of Robert Hight's Ford Mustang funny car blew off toward the end of a run when his engine exploded, but fortunately, the two fans evaluated after the incident were later released without serious injury.
As you can see in the image above, the body flew high into the air before landing on a walkway in front of the grandstands, a bit of happenstance that likely gave most fans enough time and space to move out of the way. Scroll down to watch a couple of videos showing what happened, including one from a fan's perspective that also reveals what appears to be part of the body's metal bracing landing dangerously close to the crowd.

Aluminum lightweighting does, in fact, save fuel

When the best-selling US truck sheds the equivalent weight of three football fullbacks by shifting to aluminum, folks start paying attention. Oak Ridge National Laboratory took a closer look at whether the reduced fuel consumption from a lighter aluminum body makes up for the fact that producing aluminum is far more energy intensive than steel. And the results of the study are pretty encouraging. In a nutshell, the energy needed to produce a vehicle's raw materials accounts for about 10 percent of a typical vehicle's carbon footprint during its total lifecycle, and that number is up from six percent because of advancements in fuel economy (fuel use is down to about 68 percent of total emissions from about 75 percent). Still, even with that higher material-extraction share, the fuel-efficiency gains from aluminum compared to steel will offset the additional vehicle-extraction energy in just 12,000 miles of driving, according to the study. That means that, from an environmental standpoint, aluminum vehicles are playing with the house's money after just one year on the road. Aluminum-sheet construction got topical real quickly earlier this year when Ford said the 2015 F-150 pickup truck would go to a 93-percent aluminum body construction. In addition to aluminum being less corrosive than steel, that change caused the F-150 to shed 700 pounds from its curb weight. And it looks like the Explorer and Expedition SUVs may go on an aluminum diet next. Take a look at SAE International's synopsis of the Oak Ridge Lab's study below. Life Cycle Energy and Environmental Assessment of Aluminum-Intensive Vehicle Design Advanced lightweight materials are increasingly being incorporated into new vehicle designs by automakers to enhance performance and assist in complying with increasing requirements of corporate average fuel economy standards. To assess the primary energy and carbon dioxide equivalent (CO2e) implications of vehicle designs utilizing these materials, this study examines the potential life cycle impacts of two lightweight material alternative vehicle designs, i.e., steel and aluminum of a typical passenger vehicle operated today in North America. LCA for three common alternative lightweight vehicle designs are evaluated: current production ("Baseline"), an advanced high strength steel and aluminum design ("LWSV"), and an aluminum-intensive design (AIV).

'Car Wars' says Ford, Honda to pick up share, Fiat-Chrysler ambitions downplayed

Don't look for a tremendous shifts in automotive market share over the next three years because it might not be coming. That's at least according to the annual Car Wars report by John Murphy, from Bank of America Merrill Lynch Global Research.
In the report's analysis of automakers' market share from 2013 to 2017, it predicts only small changes among the major companies. Ford and Honda see the biggest positive effect with an estimated 0.5 percent increase in their shares over the next three years; to 16.2 percent and 10.3 percent respectively. On the flip side, European automakers and Nissan are expected to lose 0.2 percent each to fall to 8.3 percent and 7.8 percent each respectively. The rest of the industry is predicted to hold steady as it is now.
The biggest loser in that prediction might be Fiat-Chrysler Automobiles. The report certainly throws a wet blanket on its plan for significant gains in market share. Murphy told The Detroit News that the company's goal was "almost unattainable."